• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

NV3550 Won't Shift into Gear

Jambi

Contributor
Jr. Member
Joined
Aug 3, 2012
Messages
137
Loc.
Littleton, CO
I just completed the NV3550 conversion and after starting my Bronco I can't get the transmission to shift into gear, it just grinds and won't go into gear. When the transfer case is in neutral, I can get the transmission to shift into gear without grinding, but when I have the transfer case in 2Hi, the transmission just grinds and won't shift into gear. This is the first time I've done a conversion like this, but I tried to educate myself as much as possible by reading the tech article that's available on this site, I watched all the Tom's Offroad videos on the conversion, and everything fit together cleanly and fairly easily, but I must have something wrong. Any thoughts would be appreciated.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
the clutch is not releasing. Any details you can provide on the clutch, hydraulic or mechanical? pedal feel, amount of free play etc.?
 
OP
OP
Jambi

Jambi

Contributor
Jr. Member
Joined
Aug 3, 2012
Messages
137
Loc.
Littleton, CO
the clutch is not releasing. Any details you can provide on the clutch, hydraulic or mechanical? pedal feel, amount of free play etc.?
I should have noted that everything needed for this conversion is brand new and I had the NV3550 rebuilt by a reputable transmission shop. I bought the NV3550 conversion kit from WH that includes the Centerforce clutch, I bought the flywheel and all necessary clutch pedal linkage, clutch fork, throwout bearing from Toms. I have been questioning if I have the linkage correct, particularly the clutch adjustment rod. The clutch pedal pushrod I have is the model for the 1 - 2" body lift, but I had to tighten the forks on the ends to their max tightness to be the correct length from the pedal to the equalizer bar. I'm not quite sure how to describe the pedal feel. I guess I would say it's pretty smooth and pushes to the floor. Tiny bit of play in the pedal before the linkage actually moves.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
As noted, clutch issue. It works with the transfer case in neutral since the output shaft is free to spin. The syncro is matching the output shaft speed and allowing the transmission to go into gear. Note: you won't get the transfer case in gear when the transmission is in gear.

Hopefully it is just a clutch linkage adjustment and not the clutch disk installed backwards. That's assuming you used stock Bronco linkage and bellhousing.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
@Broncobowsher brings up a good point that I’ve been guilty of, installing the disc backwards. It will never release. I have no doubt it is either a linkage issue or the disc backwards. We see a lot of “my new transmission or clutch install won’t go into gear” it is almost always a linkage issue of one sort or another. not one time do I recall it ever being an issue with the transmission.
 
OP
OP
Jambi

Jambi

Contributor
Jr. Member
Joined
Aug 3, 2012
Messages
137
Loc.
Littleton, CO
Thanks for the input. I'm really hoping it's a linkage issue. I was confident I checked and double checked I had the disc on correctly, but now I'm second guessing.
 

CowboyGrin

Contributor
the circus looks like fun
Joined
Jan 20, 2021
Messages
175
Loc.
Oklahoma
@Broncobowsher brings up a good point that I’ve been guilty of, installing the disc backwards. It will never release. I have no doubt it is either a linkage issue or the disc backwards. We see a lot of “my new transmission or clutch install won’t go into gear” it is almost always a linkage issue of one sort or another. not one time do I recall it ever being an issue with the transmission.
Not to highjack, but the timing of this thread is spot on for me. Worried I might have a similar issue with an AX15 install that I just dropped in last weekend on my frame-off build. Once all bolted up, I rachet-strapped the clutch fork back to test it. The throwout bearing does move in about 1/4” as the fork is pulled back, but the output shaft doesn’t turn as freely as expected. Barely moves in 4th gear with the clutch fork pulled as far back as I could get it. Can’t get it to turn in any other gear. Is this normal for new components or am I’m facing a similar situation as the OP? Now would be the time to get it right before moving forward.

I’m 99% sure the disc isn’t backwards but 100% sure my memory is capable of getting that backwards. Using a Centerforce II disc/pressure plate and Centerforce flywheel combo for the first time so don’t know what to expect. Maybe I need a different throwout bearing or clutch fork to get more pressure on the diaphragm for this setup?
 

Attachments

  • IMG_8629.jpeg
    IMG_8629.jpeg
    252.9 KB · Views: 143
  • IMG_8628.jpeg
    IMG_8628.jpeg
    217.8 KB · Views: 136

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
How easily does the output shaft turn in neutral? And what are you turning it with?
On these it’s kinda hard to get a good grip I think. Do you have a tool of some kind?
 

CowboyGrin

Contributor
the circus looks like fun
Joined
Jan 20, 2021
Messages
175
Loc.
Oklahoma
How easily does the output shaft turn in neutral? And what are you turning it with?
On these it’s kinda hard to get a good grip I think. Do you have a tool of some kind?
Using a visegrip on the shaft being careful not to damage the splines. Not going crazy with it, but enough to know there is more friction than anticipated. Turns easy in neutral, more like what was expected for in gear when disengaged.
 
Last edited:

ssray

Contributor
Sr. Member
Joined
Apr 19, 2010
Messages
922
Loc.
South Central NE
Here‘s a link to a Jeep TJ forum post that has a list of manuals. If you would like a manual for that 3550 for some point down the road you can download the pdf from there. Also AX5, AX15 and NSG 370 as well for anyone that could use them.

Manuals
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
OK, you said grinding, if you are clutch pedal in, there should be zero grinding as there should be no spinning of rotating mass. This would also make it hard to get into gear.

Does it grind engine off? Does it go into gear engine off?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Exactly. Did you say whether or not it shifts easily when the engine is not running?
 
OP
OP
Jambi

Jambi

Contributor
Jr. Member
Joined
Aug 3, 2012
Messages
137
Loc.
Littleton, CO
@DirtDonk and @73azbronco not sure if you were asking me or @CowboyGrin, but my NV3550 shifts easily through all gears when the engine is not running. When the engine IS running and clutch pedal is depressed there is no grinding. The grinding occurs when I attempt to shift into first (or any gear for that matter), and I can't even get it into gear it grinds so bad.

Also, I hated to do it, but just had to confirm--I pulled everything out yesterday to check the disc and I DID have my disc on correctly.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
It is something in the clutch. Hard to really tell at this point. I am hoping you still have the clutch apart. Make sure the clutch disk didn't get bent (that can happen if fighting getting the transmission to install and getting at a severe angle while engaged to the clutch disk). You have both dowel pins in the back of the block to align the bellhousing correctly to the block? Double check that the disk didn't get marked backwards. It's just going to be a bunch of detective work in the clutch area.
 

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
If you have it apart take some pictures.

Been awhile since I've done any clutch work. I seem to recall different lengths of throw out bearings. Also clutch fork and pivot. Knowing the free play and feel through the travel really helps.

Just because it's new doesn't mean it's good. You can trust but you must verify everything. Save yourself some headache and follow advice completely with no short cuts or guessing.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
@DirtDonk and @73azbronco not sure if you were asking me or @CowboyGrin, but my NV3550 shifts easily through all gears when the engine is not running. When the engine IS running and clutch pedal is depressed there is no grinding. The grinding occurs when I attempt to shift into first (or any gear for that matter), and I can't even get it into gear it grinds so bad.

Also, I hated to do it, but just had to confirm--I pulled everything out yesterday to check the disc and I DID have my disc on correctly.
That confirms an issue with the linkage not pushing the throw out bearing far enough for it to disengage the clutch.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Your signature says you have a 1 inch body lift. Do you have an extended pedal rod?
You might not be getting enough adjustment out of the fork rod.
And do you have a standard original 69 Bell crank? Has it been modified in any way? Has it been updated with bushings and seals?
Maybe it’s flopping around.

Did you have someone push on the clutch while you were looking? I think this was already talked about, but I don’t remember if you said you did.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Along the same lines, what year is your 351? What bell housing?
Did it have both both holes for the clutch linkage, or did you have to add it?
If you needed it, but are only using one bolt, it might not be enough.
 
OP
OP
Jambi

Jambi

Contributor
Jr. Member
Joined
Aug 3, 2012
Messages
137
Loc.
Littleton, CO
@DirtDonk, all my clutch linkage from the pedal rod to the clutch fork is all new. I got the extended pedal rod for 1" - 2" body lift but I had to tighten the forks on both ends as far as they would go, in order to make the end to end length (fork to fork) the shortest it could be to fit from the pedal to the bell crank, otherwise it's just too long. At first, I thought I was sent the rod for a 2" - 3" body lift by mistake. I bought the clutch bell crank kit that's available from the vendors as well as the clutch fork push rod. My 351 is a '94 but I'm not sure about the bell housing. I also bought the EFI clutch equalizer bracket, however the bell housing does not have the hole for that second bolt (bell housing bolt) for the engine side clutch bell crank so I had to fab something up to use the single bolt. It's crude, but seems to allow the pedal rod to move the bell crank through the entire motion allowed by pedal and pedal rod.

While I have the transmission out again, do you think I should tap a hole in the bell housing for that second engine side bell crank bolt?
 
Top