• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

399strokerEB

Contributor
Bronco Guru
Joined
Jun 23, 2010
Messages
1,733
Loc.
Wasilla, AK
Drug the plow bronco into the shop to give it a once over and let it thaw out. I haven't got to use this thing once this winter.
20251227_174836.jpg


I also have the aod about wrapped up, just need to finish the pump and get a torque converter, and order a couple small parts from wild horses.
20251227_174804.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That’s an understatement!
Oy vey they’re expensive these days.
It’s always been one of those items that seemed to be more than the market needs. But now with big truck tires, it’s even worse.

I remember I bought my first set of 11–15 Armstrong true tracs for $49 each. Back then, that seemed kind of expensive as well.
 

Bruners4

Full Member
Joined
Jul 22, 2019
Messages
286
Loc.
1/2 way to everywhere
I don't post in this one often as I probably should. Going to sum up this last week of items done.
'96 Bronco - My rear window motor relay pack that I designed built and documented here [https://www.fullsizebronco.com/threads/80-96-tailgate-window-motor-relay-modification.510376/] stopped moving the window "up". Found #85 connector had pulled out of the plug that is the ground for the relay coil. This was caused by the zip tie breaking and the relay pack fell and then the window lowered onto it. Also had the cigar lighter in the ash tray quit working. Found both wires had flexes too many times and broke. Repaired these two wires with new 'flexible' wires and a service loop. Treated the leather seats with a leather moisturizer.
'69 Bronco - Cleaned air filter and reoiled it. Checked and tightened body mount bolts. Re-strapped jack to roll bar to stop rattle. Tightened GMRS whip antenna. Treated the leather seats with a leather moisturizer.
'21 Bronco - Filled with fuel and checked tire pressures.
'68 Bronco (2nd) - Got title switched over to my name.
 

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,707
Loc.
NH
Got my new heater core and plug wires in the garage waiting for a decent weekend to remove the box. Other than that? just dreaming of nicer weather....
 

Bruners4

Full Member
Joined
Jul 22, 2019
Messages
286
Loc.
1/2 way to everywhere
Exhaust note was a little raspy at times when in the throttle more than cruising. First noticed it when we were at BSC CO in the thinner air. Researching this I found a spiral baffle that goes into the exhaust pipe. Placed it in the 3" exhaust pipe before the muffler.
Measured WFO DBs (iPhone app) at stall RPM before: 109, after: 101.
It is just right now!
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
In today's (actually yesterday's) episode of the Bronco Life, got the heater hoses all plumbed in and had the Bronco running to heat it up so I could sit in it with the heater blowing hot air on my feet. You do realize it was sunny and like 65 out here yesterday, which in SoCal is almost a blizzard...

So anyways, as I'm fighting frost bite the heater is working awesome, toes are nice and toasty, but along with the thump of the exhaust I'm hearing a squealy squeaky whinny noise coming from the engine. Not a tap tap tap or sput sput sput, it was low level whine that comes and goes. So I do to my new power steering box and listen close... nothing. Go to the new alternator... Nothing. stand in front and lean over the radiator and wouldn't you know it... my multi decade old water pump is not happy. Fluid level was fine and clean. I figured it was finally time.

Picked up the parts (had to go to three different auto parts stores) after visiting the Napa Warehouse and they didn't have it in stock. Oh well.

Started pulling it apart and here is what I found. It was a great teaching moment for my boys demonstrating exactly how a thermostat is supposed to fail properly. Also, I got to show them what decades of service does to these old parts and the issues with putting half a tube of RTV gasket maker on the thermostat housing (probably my fault as I think I replaced that a couple years ago but don't remember).

Its service time has expired.jpg

Just doing its thing.jpg

Current situation in the engine compartment
Current situation.jpg


Of course in most cases I can't just leave parts alone so I fired up the tempurature controlled paint both and cleaned up some pully's and brackets.
High end paint booth.jpg

Ran out of time to finish the install but figured if the Thermostat housing was in that condition, what does the inside of the water pump look like... Well, here you go...
WP Internals.jpg

After pulling that apart I did a hose flush on the engine block, radiator, and heater core box just to make sure all the old fluid was gone and only clear water was coming out. Not too surprised it was actually pretty clean fluid as I did refill it all at the beginning of 2025 when I installed the new radiator hoses.

That was all for yesterday. Today, first thing will be installing the new water pump and hooking it all back up, then going for a nice little test drive if these winds ever die down.
 

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
Cut out a couple of interior panels yesterday and got them fitted. I also ordered some dark gray marine vinyl and foam backing for covering them. Also ordered some LED courtesy lights for under the dash and back corners of the panels. Also hooked up backup camera for the radio display. (Pic didn't come through)

IMG_0658.jpeg
IMG_0659 (1).jpeg
 

Attachments

  • IMG_0659 (1).jpeg
    IMG_0659 (1).jpeg
    190.8 KB · Views: 95

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
Apparently I work slow. After 20 years sitting on all the parts I finally took my glove box out of the center console and did a sliding mount on it. Middle picture is where I have to slide it over to clear the bar.
 

Attachments

  • Closed.JPG
    Closed.JPG
    207.5 KB · Views: 127
  • Half open.JPG
    Half open.JPG
    172.9 KB · Views: 129
  • Open as modified.JPG
    Open as modified.JPG
    223.6 KB · Views: 111
Top