• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. B

    Drum brakes will not stop straight

    While drum brakes are a old design they are still in use in the front on many new over the road trucks dump trucks and the like,. Properly setup they will out stop disc brakes, But there are drawbacks #1 is the brake pull you have now. #2 drum brakes will fade when hot and they build more heat...
  2. B

    Vacuum Reading Help

    A vacuum leak wont always make the needle bounce around. A small vacuum leak will increase idle speed and if its not leaning out the fuel mixture to much you'll never know it just by a vacuum gauge reading. But it will show up when you try to adjust the idle mixture screws and you find that you...
  3. B

    Type F versus Dex/Merc

    The only real difference between automatic tranny fluids is type F doesn't have any friction modifiers added to it where mercon/dextron does. The friction modifiers were added to produce softer shifts. Most likely you wont notice any difference by adding merc/dex it may shift smoother that's...
  4. B

    Vacuum Reading Help

    At idle you shouldn't have any vacuum on the vacuum advance but its a good idea to plug it as you did anyhow for testing. Steady is good 1/2in. hg is not bad with some carb and or timing adjusting you should be able to get it steadier.
  5. B

    DuraSpark Distributor - Too fat for the hole

    Sounds like the housing is the 351/400M/460 type which I believe had a slightly larger shoulder than the small block and your shaft appears to be the later style for 87 up engines. You might have a steel gear as well for a roller cam. The main issue is that most of the ford housings look the...
  6. B

    Torker 289

    I ran a 289 torker on my 73 for many years well over 20, it seemed to work fairly well. Its RPM range is the same as a ebelbrock RPM manifold. But I would not suggest using a torker manifold Single plane manifolds and heavier vehicles are not the best mix also it will require a hood scoop as...
  7. B

    Lost Oil Pressure - ITS FIXED! Update on page 2

    As was said at least pull the pan and replace the oil pump and check the rod and main bearings. The pump could have locked just long enough to break the dizzy shaft. I wouldn't trust it. And the short drive home may have damaged the bearings. If the bearings look good then I would say you got...
  8. B

    302 cam choice?

    The 255 is fairly easy to ID as the intake manifold will look funky. its sort of a open runner design with a stamped steel valley pan under it like the old Yblock engines. Also intake ports will be round instead of rectangle like a 302.
  9. B

    Timing Help Needed

    You could probably run 12-14 degrees initial timing. Everything else sounds good. don't worry much about what your getting with vacuum hooked up as was said its load dependent and reacts different when actually driving. Basic rule is to run as much timing as you can as long as the engine is not...
  10. B

    front calipers for conversion

    Or if you don't want to remove a hub to figure out what spindle you have just look at the calipers themselves. the GM caliper will have 2 slider bolt/pins holding the caliper to the backing plate which is maybe 1/4" stamped steel. If you have ford style brakes the caliper bracket is thicker cast...
  11. B

    aluminum heads or cast

    The aluminum head problems were mostly due to old factory heads on some vehicles and more to do with casting/design issues than anything else that's where aluminum got a bad rap. Times have changed designs and processes are much better to the point almost the whole engine can be made out of...
  12. B

    ho cam 4 degrees advance & gt40 springs

    Its not really high RPMs that affect the valve springs. Its the amount of lift involved and if said springs will accept the lift of the cam without the coils touching each other. But high RPMs if you have weak springs then you will have valve float where at low RPM's you may never have a issue...
  13. B

    New Front Coils!?

    Id say your coils look pretty normal for progessive springs. New ones may be the same as Ive seen several broncos with new progressive coils and they are that way. Id do some measuring first but like you said coils are fairly cheap and easy to replace so new ones wont hurt. While I'm sure coils...
  14. B

    forged pistons

    Your friend is correct your engine will last longer if you allow it to warm up some before just taking off. That applies to pretty much any piston that is used although as they said forged kinda requires it. Most people in todays world just jump in and take off that's not real good for a engine...
  15. B

    New Toy - Just Trucks

    Ive been hunting that one as well. I believe they also have a black one that size as well. I just find lots of the smaller ones.
  16. B

    302 heads

    Lots of options and lots of good suggestions. I would really tear your current engine down find out what you actually have. I'm not certain but I think that broncos may have stayed with 58cc heads. Id check out what you have before looking at getting a set of 289 heads as they will be the same...
  17. B

    Fix your door latch before it's to late!!!

    I kinda agree with the not sandblasting comment. Maybe not so much for wear issues but for rust issues. As you have effectively removed all the plating that was protecting the metal. Another method for removing the grim is oven cleaner. Ive done it several times doesn't hurt the finish so no...
  18. B

    AZ Stampede

    Stampede went pretty well. Raffle was pretty good as well don't win anything I think it was bad luck going without my bronco. but good all the same. Thanks to all the vendors that donated. Crowd was smaller than in years past but still a fair amount of people. Offhand only heard about a couple...
  19. B

    trying to keep my 68's value and history.

    Disc brakes were never a option on a 68. They didn't become available until late 75 and standard on 76 up broncos. As to hurting its value well its debateable. On one hand if your want something all original then it could hurt. But in the case of disc brakes at least front disc the conversion is...
Top