• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

new heads ?

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
My 302 smokes 2 packs a day, got to tear it down. How do I find later model heads for my 1973? Is going to a wrecking yard for engine parts ever more than a "pig at a poke"? Will a wrecking yard sell heads without the whole engine if the engine isn't worn out? I have stock 1973 exhaust manifolds. Do I need different x manifolds with newer heads? Thanks
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
My 302 smokes 2 packs a day, got to tear it down. How do I find later model heads for my 1973? Is going to a wrecking yard for engine parts ever more than a "pig at a poke"? Will a wrecking yard sell heads without the whole engine if the engine isn't worn out? I have stock 1973 exhaust manifolds. Do I need different x manifolds with newer heads? Thanks

The E7TE heads are plentiful and a perfect match for what you have now as far as intake and exhaust.

But why?...you are not really going to gain much from a later model head, if anything at all. And I would never trust any wrecking yard set of heads to be ready to bolt on...so the machine shop work and cost is the same regardless.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
X2 on the above. E7's are going to be an improvement over the 70's smog heads but without other modifications you're not gaining much. They will work with the stock exhaust manifolds.

Expect heads from a "yard" to need tanking/washing, magnafluxing and a valve lapping minimum. I pulled a set of GT40P's off a 2001 Mount and they were in good enough shape to run after the above was done.

Smoking 2 packs a day could be more than valve guides. Might be a ring issue as well as valve guides.

Tim
 

chickenman

New Member
Joined
Jul 8, 2013
Messages
44
Loc.
Edmonton Alberta
I pulled a set of heads off a '96 5.0 in the pick n pull without issues. Just make sure you bring enough tools and a break bar. If youre looking to have them re built you should check into that cost. By the time i had them rebuilt i was within a few hundred dollars of the set of aluminum heads... so do a bit of homework before hand
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
E7 heads have improved exhaust flow over the older design. However, you need to keep a close eye on the combustion chamber size. You don't want to reduce your compression ratio.
If you plan any engine work on a small block Ford, you need to get this book.
It covers, in detail, most of the work you'll encounter.
It has a whole section on cylinder heads. It shows the compression ration you can expect with different cylinder head combinations and the evolution of cylinder heads on the small block Ford Motor.

https://www.barnesandnoble.com/p/re...MIt-SogYiw2AIVgcVkCh0OQQWpEAQYBCABEgJxq_D_BwE
 
Last edited by a moderator:

Cooper

Full Member
Joined
May 7, 2006
Messages
309
Loc.
Northeast
Would you mind just posting the title / author of the book you are recommending. The link you posted for Barnes & Noble only yields this:

"We found 0 results for reb...CABEgKTqfD_BwE. Please try another search or browse our recommendations below."
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I use "How to Rebuild Small-Block Ford Engines" by Tom Monroe

Covers everything I needed to know to rebuild my 351W

Tim
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, I would do a compression test before pulling it apart. If the compression is good you have other options, like new valve stem seals. Good luck
 

Cooper

Full Member
Joined
May 7, 2006
Messages
309
Loc.
Northeast
Hello blubuckeroo; thank you for posting that information. That makes two recommendations between you and Timmy. I'll have to check it out.
 
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
The 302 has a edelbrock manifold and carb. I will put on headers if the gain is worth it. I'm inquiring about heads because I suspect I'm going to have to spend money already on my current heads, might switch and spend the same money rebuilding better heads. I'm likely going to have to rebuild the block- will look at the cylinder tapper when I get the heads off. The engine has great power now- just leaves a cloud of blue whenever I'm giving accelerator. I truly appreciate your knowledge and the input you give! (I took compression recently- can't find the numbers but I believe 138 low most 150/155. I will take the compression again, with and without oil, and post the numbers. Thanks again for your help. I suspect I'm going to spend 3 to 5 k, any thoughts on other routes?
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Go to your local machinist and i bet he has a set on a shelf in back either in good shape or already built up.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Go to your local machinist and i bet he has a set on a shelf in back either in good shape or already built up.

Took the words right out of my mouth.
Years ago as in 25+ years ago I clearly remember hitting junk yards to find heads worth rebuilding. Bought Harland Sharp Roller Rockers, guide plates, hardened pushrods, etc... Took them to my local machine shop.
When I came back to pick up the heads the owner happened to be there. He cashed me out. Then said I wish I was here when you came in....I would have given you these heads (pointing to the shelf) for less than what you have invested with what you now have now.
They were very, very good heads that some body never picked up months before.
So I always said that next time I will go straight to the machine shop first.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
The 302 has a edelbrock manifold and carb. I will put on headers if the gain is worth it. I'm inquiring about heads because I suspect I'm going to have to spend money already on my current heads, might switch and spend the same money rebuilding better heads. I'm likely going to have to rebuild the block- will look at the cylinder tapper when I get the heads off. The engine has great power now- just leaves a cloud of blue whenever I'm giving accelerator. I truly appreciate your knowledge and the input you give! (I took compression recently- can't find the numbers but I believe 138 low most 150/155. I will take the compression again, with and without oil, and post the numbers. Thanks again for your help. I suspect I'm going to spend 3 to 5 k, any thoughts on other routes?

Yes.....JMO

I wouldn't spend a dime rebuilding a 70's 302. I would find a running explorer and pull the 5.0 out of it and drive it till it needed rebuilding. You would have the explorer front dress which works great on the bronco, all the parts for an EFI swap if you ever go that route and a roller cam 5.0 with GT40 or GT40P heads and a darn good stock cam. Also the transmission in the bronco is a popular swap.

Doing this will likely double the HP you currently have.

Just an example...I've seen them in the $1500 range.
https://littlerock.craigslist.org/ctd/d/ford-explorer-awd-eddie-baurer/6422498296.html

I went the 351W route.....took my old 302 to the scrap yard....

Tim
 
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
A mechanic friend suggested leaving the exhaust manifold attached to the head, pull the head, then remove the manifold. Said the bolts holding on the manifold are easier to remove on the bench. Anyone pulled a 302 head with the exhaust manifold still attached? Thanks
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
A mechanic friend suggested leaving the exhaust manifold attached to the head, pull the head, then remove the manifold. Said the bolts holding on the manifold are easier to remove on the bench. Anyone pulled a 302 head with the exhaust manifold still attached? Thanks

Sure. I've pulled the heads off many an engine with exhaust manifolds still bolted on to them
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I wouldn't waste time or money on E7TE heads. Find some '96-early '97 GT40 heads from an explorer or mountaineer. Stock manifolds fit, you get hard valve seats and springs are good enough for a stockish flat tappet cam. I would have them rebuilt though.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
As was said do a compression check and if it checks out hit up the machine shop. They usually always have heads available. now the down side is pretty much any stock head out there is going to cause a loss in compression as most if not all broncos had small 58cc chambered heads. plus 73 was like 8.3-1 comp ratio. Most of the other heads out there will have larger chambers usually 62-64cc some as big a 69cc so check what you get. With 62-64cc you lose a bit of compression with those not so good in a already low compression motor. Also keep in mind that 77up heads require different rocker arms so that could be another cost.

Upgrading to a newer engine can be nice but there are costs involved to swap them in. some planning and careful shopping can help but if your in need of a new engine there is nothing wrong with rebuilding what you have it will probably cost less and you wont need extra parts to get it swapped in.
I'm a fan of headers over most other mods small fords have poor exhaust ports and headers help way more than intake and carb upgrades. engines are basically a air pump the easier air flows throw it the more power that can be made. I would consider upgrading the camshaft as well that will put the power where you need it with the right pick.
 
Top