• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

306 Build Cam Choice

latrucker

Contributor
Sr. Member
Joined
Jul 19, 2010
Messages
647
I ran the 35-510-8 on my 306 before I had to pull the motor for various reasons. I loved the way it pulled, great bottom and mid power. I could actually idle up the ramps when loading my bronco on my trailer. Could never come close to doing that with the stock cam. Pulled strong till around 5000 rpm. Only negative is the valve train noise that it makes. Lots of ticking, almost sounds like bad lifters. Everyone who runs this cam says the same thing, if you can put up with the valve train noise you will love it. I am building a 331 with a custom cam and may be selling the XE258HR that u are looking at buying. Let me know if u have any interest.
 
OP
OP
skerrybronco

skerrybronco

Sr. Member
Joined
Aug 17, 2012
Messages
818
Loc.
Montreal,Canada
nice thread and numbers, but I still want to stay in the lower end numbers,
waiting for my engine builder to get back from holidays to make final decision
thats why I'm here doing the research as well
 

latrucker

Contributor
Sr. Member
Joined
Jul 19, 2010
Messages
647
OP
OP
skerrybronco

skerrybronco

Sr. Member
Joined
Aug 17, 2012
Messages
818
Loc.
Montreal,Canada
latrucker
what heads and valve train were you using, trying to narrow down the noisy vale train
I know my afr's valve springs were upgraded, I am wondering if this would make a difference
thanks
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Problems with the valve train noise may not be the Cam at all.

Does the rest of the Valve Train match the Cam?

The XE258HR is a very good low end torque cam, but it does have a lot of lift that the factory hardware cannot support. An added benefit is that you can convert to EFI with this Cam as well.

Best to get the complete Cam kit (K-Kit) if possible. Everything matches (made for each other) and vastly decreases the chance of any problems.
 

gambling209

Full Member
Joined
Apr 20, 2010
Messages
198
i run that trick flow cam talked about above in my 66 mustang. while not a bronco, it does pull down low. has a lumpy idle and no valve train noise. for a roller cam it is cheap. i probably would run a smaller cam in a bronco.
 

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
Best to get the complete Cam kit (K-Kit) if possible. Everything matches (made for each other) and vastly decreases the chance of any problems.

This is what I did with 266 cam for my 347. Fewer questions on reliability with a matched combo!

Do yourself a favor on price... Google the kit part number and find the lowest price- then call Summit of Jegs for a price match. They will have these on the shelf with very cheap shipping! I used a race-mart.com price for my cam and saved about $100 or so. Got the kit in two days with standard ground$12.95 shipping from Summit!
 

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
Complete kit I got for a roller motor.

1C576894-ECAD-4166-BF84-249799B5CB4A-1113-000001685E9B318A.jpg
 

latrucker

Contributor
Sr. Member
Joined
Jul 19, 2010
Messages
647
latrucker
what heads and valve train were you using, trying to narrow down the noisy vale train
I know my afr's valve springs were upgraded, I am wondering if this would make a difference
thanks
Not running comp springs but exact same specs as they recommend. I have run this cam on Gt40 iron heads and AFR165, same results on both. Comp techs have told many people complaining about valve train noise on the extreme energy series cams that it is normal. Comes from the the aggressive ramp rates. Short duration and high lift makes the valves slam open and shut at a very fast rate thus creating the valve noise. I am guessing it is the velocity at which the valve hits the seat. It never caused any problems just had a very rythmic ticking at idle. Almost sounds like a sewing machine.
 

latrucker

Contributor
Sr. Member
Joined
Jul 19, 2010
Messages
647
Glad to help. It really is a bad a** little cam. It will pull hard till 5000 rpm's maybe a little higher but not much. I will try to find the article with dyno results that made up my mind to buy it. I'll post a link as soon as I find it.
 
Top