• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

72 carb questions

gunnibronco

Contributor
Sr. Member
Joined
Apr 13, 2008
Messages
628
Loc.
Gardnerville, NV
I'm trying to put my 72 Explorer Sport back on the road. It sat for 5+ years before I bought it in 2016 and another 9 years since. It's going to be a *mostly* original patina build. I'm replacing the fuel system (tanks, pumps, lines, carb rebuild) and brake system in their entirety before starting it.

I don't know a lot about carbs and need basic education and some pointers. I'd feel more confident in doing an Explorer EFI swap than this. LOL

It is running 46P jets. I now live at 4700', but the truck lived at 7700'+ most it's life. Is the 46P jet close to what I need? I haven't messed with any of the settings, except for the idle screws. They were set about 4.5 turns out from stop, most the videos I watched said 2 turns out +/-, so that is where I set them. Compared to what I'm seeing on the rebuild videos, mine is super clean, and may have been recently rebuilt.

I put in a carb rebuild kit yesterday. I think I found it has 2 dash pots/vacuum breaks, one electric and one mechanical. Again, this is new to me and I don't really know what the heck I'm looking at. Is this correct? Why are there 2? Should I replace both? I'm assuming the mechanical one should be replaced, it looks like a diaphragm and I don't trust it to work.
1746026640304.png


1746026659520.png


It also has a choke vacuum break.
1746027175801.png

And it was changed to a manual cable choke. I want to remove the manual choke and return to stock heat activated choke or an electric choke kit. I lean towards the stock choke because "stock" is my general goal with the build. It won't be a daily driver and won't get driven much in the winter.
1746027344495.png


All advice, insights, web links are all appreciated. I'd like to shoot for as reliable as possible, so please let me know what parts are possibly still useable or should be replaced.
 

serial car restorer

Yes, I'll restore almost anything...
Joined
Aug 27, 2024
Messages
742
Loc.
Western Oregon
I recently swapped the original manual choke carb on my '69 for a '72 carb, primarily to ease the addition of an automatic choke. I rebuilt it completely, and converted the '72 hot-air choke to electric. (All parts came from Mike's Carbs.) Both emissions dashpots have been removed to simplify the system, and it has 48 main jets for low altitudes (0-2000 feet). Runs nicely.

IMG_5496.jpeg


IMG_5533.JPG


IMG_5534.JPG
 
Last edited:
OP
OP
gunnibronco

gunnibronco

Contributor
Sr. Member
Joined
Apr 13, 2008
Messages
628
Loc.
Gardnerville, NV
I recently swapped the original manual choke carb on my '69 for a '72 carb, primarily to ease the addition of an automatic choke. I rebuilt it completely, and converted the '72 hot-air choke to electric. (All parts came from Mike's Carbs.) Both emissions dashpots have been removed to simplify the system, and it has 48 main jets for low altitudes (0-2000 feet). Runs nicely.

View attachment 943711

View attachment 943712

View attachment 943713
Thanks. So my 46 jets may be ok at my altitude, at least close enough to get a baseline.

Between a neighbor and an email to Mike's Carb Parts I think I've figured it all out. I'll be ordering a few parts from Mikes this weekend to finish everything up.

I know I'm fighting an unnecessary battle with all the carb and emissions stuff in the 72. It's a patina build and my goal is to maintain as much originality as reasonably possible.

I found that the externally mounted vacuum device is bad, Mikes called it an antistall dashpot. It's no longer produced but I was lucky enough to find a NOS part.

The electric solenoid is a throttle position solenoid. I don't know when is receives 12v or not. But it bench tested ok.

The choke pull down diaphram is available. So I think I have all the parts covered at this point.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The electric solenoid gets power any time the key is in the ON position. It’s how you set your curb idle.
The idle speed adjusting screw is turned down to a lower “base idle“ to avoid dieseling/run-on when the key is turned off.
Set your “base idle” speed to, for example, 450 to 500 RPM with the screw. Then set your “curb idle“ speed to, for example, 600 to 650 RPM with the electric solenoid adjustment.

It’s not strictly necessary for the vehicle to run properly. When to normally, and when utilizing only a vacuum Advance as opposed to the dual advanced/retard set up that a 72 would have come with, run on is not a huge issue.
But it’s still a nice thing for a sharp clean shut off.

The choke pull-off, of course is necessary assuming an automatic/electric choke.
The previous owner probably converted to manual because of the high altitude. No matter what your jet size, a choke is often overkill to not necessary at high altitude. Or if so, minimal choke is preferred.
In the old days, it was often very hard to start a vehicle at high altitude with an automatic choke. They tended to flood out if they were tuned for low altitude. Maybe the PO, even with the tune and for altitude carburetor, found trouble with his choke settings.
Or simply was old-school and preferred a manual choke no matter what.
When we used to drive up to high altitudes with our normally low altitude, tuned vehicles, we always blocked the choke open with rubber bands once we got to altitude.

The additional vacuum operated solenoid on the back of the carburetor could be part of that ambient switch system mentioned in your other thread.
If so, even if it doesn’t work, don’t toss it out.
Block it off if needed, but keep it for the originality. Not many Broncos were so equipped.
Or it could be, even more rare, as part of the “altitude compensating” carburetor system that was available on some 2100s. Or maybe that was essentially the same thing.
I personally never seen one, but maybe that’s what you have?
 
OP
OP
gunnibronco

gunnibronco

Contributor
Sr. Member
Joined
Apr 13, 2008
Messages
628
Loc.
Gardnerville, NV
The electric solenoid gets power any time the key is in the ON position. It’s how you set your curb idle.
The idle speed adjusting screw is turned down to a lower “base idle“ to avoid dieseling/run-on when the key is turned off.
Set your “base idle” speed to, for example, 450 to 500 RPM with the screw. Then set your “curb idle“ speed to, for example, 600 to 650 RPM with the electric solenoid adjustment.

It’s not strictly necessary for the vehicle to run properly. When to normally, and when utilizing only a vacuum Advance as opposed to the dual advanced/retard set up that a 72 would have come with, run on is not a huge issue.
But it’s still a nice thing for a sharp clean shut off.

The choke pull-off, of course is necessary assuming an automatic/electric choke.
The previous owner probably converted to manual because of the high altitude. No matter what your jet size, a choke is often overkill to not necessary at high altitude. Or if so, minimal choke is preferred.
In the old days, it was often very hard to start a vehicle at high altitude with an automatic choke. They tended to flood out if they were tuned for low altitude. Maybe the PO, even with the tune and for altitude carburetor, found trouble with his choke settings.
Or simply was old-school and preferred a manual choke no matter what.
When we used to drive up to high altitudes with our normally low altitude, tuned vehicles, we always blocked the choke open with rubber bands once we got to altitude.

The additional vacuum operated solenoid on the back of the carburetor could be part of that ambient switch system mentioned in your other thread.
If so, even if it doesn’t work, don’t toss it out.
Block it off if needed, but keep it for the originality. Not many Broncos were so equipped.
Or it could be, even more rare, as part of the “altitude compensating” carburetor system that was available on some 2100s. Or maybe that was essentially the same thing.
I personally never seen one, but maybe that’s what you have?
Awesome info! Thanks.

This truck lived at 7700' feet in one of the coldest towns in the US. -15* or -20* was normal. I saw -45* more than once, so choke performance and altitude was pretty important for something sitting outside. I daily drove my outdoor parked 74 most my 22 years there. I had a block heater and Edelbrock, then Mustang EFI so I just don't know these 2100's yet. The choke tube is still here so it will be going back to automatic heated choke.

I bit the bullet and found a NOS vacuum "solenoid". I hope to get it all working. The 2 switches on the vacuum system have me worried if they are working. I'll be documenting the vacuum and wiring routing, especially because of the extra 72 stuff.

1746295423786.png
1746295306339.png


1746295294321.png



1746295273399.png
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yep, what’s left of the connector in your last pic looks like the ambient switch plug.
If the transmission is original, you should see a screw-in sensor thingy somewhere on the driver side.

The valve thingy on the front corner of your intake with the blue and brown wires to it, may be part of your ambient switch system.

The blue conehead thingy on the back of the intake is the dual diaphragm advance control. Directs a mix of ported and full manifold vacuum to the distributor.
Came on pretty much all EB’s from’70 to’73 or thereabouts.
 
Top