• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

9" Third Member Question

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Pulled the pinion on my 4:11 rear to replace seal and third member is broken where pilot bearing seats. Will any third member work and swap my gears into it?
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
Any 9" case will work, but I would spend the $200-300 (4-5 choices in that range for a nodular case)...and have your gears installed in it. I wnet with the Strange Pro-case...very beefy (~315 via Summit)...but they (Strange) offer an option for $230 as well...as a side note all the Strange stuff is cast and machined here in the US. The Yukon cases are not.

Good luck.
 
OP
OP
Explorer

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
This wasn't in my budget, but gets me doing one more thing I haven't done. Going to look at a 9" in the morning that may already have 4:11's in it for $100. Just wanted to make sure the third member would work. I know something changes with gear sizes. Is it just the carrier, not the third member? Really don't have a clue about the inner workings.
 

br0nc0xrapt0r

Loves pickles
Joined
Sep 28, 2007
Messages
5,439
There is no carrier break or anything like that in the 9 any third will bolt up its the shafts that changed.
 

WyleCoyote

Bronco Guru
Joined
May 2, 2002
Messages
1,739
With the 9" there is no difference for different gearing. That is the D44 - which splits at 3.90. Installing gears in a 9" is really easy, all you need is a dial-indicator and a couple torque wrenchs.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
This wasn't in my budget, but gets me doing one more thing I haven't done. Going to look at a 9" in the morning that may already have 4:11's in it for $100. Just wanted to make sure the third member would work. I know something changes with gear sizes. Is it just the carrier, not the third member? Really don't have a clue about the inner workings.

If you plan to use the new diff as is, check the axle spline count.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
X2 main differance will be axle spline count. really only broncos, some cars, early 1/2ton trucks and vans got 28 spline axles. in the 70's pretty much only broncos and some vans had 28 spline axles so most 3rd members will be 31 spline. but for the most part you can use your gears and carrier in any third member there were some early 3rd members that use bigger bearings and there are factory nodular 3rd memebers that may also take larger bearings in either case you should be able to get conversion bearings to fit if needed.
 
OP
OP
Explorer

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Thanks again guy's. Think I got it now. Glad to hear I hadn't completly lost my mind. I knew there was a change point on gearing somewhere, I confused the front with the rear. Worst case I can use the guts out of mine. Is a used third member worth $100?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
$100 is a decent price for a complete third memeber even better if it has the gearing you need.
 
OP
OP
Explorer

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Picked up the rear end for $100 and is already has 4:11's. Susposed to be 28 spline so good to go. Even if it's 31 spline, I'll upgrade the axels. Special thanks to broncnaz. The guy had an NP435 hooked to a Dana 21 and broncnaz advised me it would work. It is 28 spline output and looks like everything will fit perfectly. $125, couldn't pass it up. Impossible to find locally. Thanks guy's.
 
Top