• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bronco Suprises

Bart

Bronco Guru
Joined
Dec 12, 2001
Messages
1,695
Loc.
Buffalo Gap, Texas
Try this one on. When I started my frame off last year I took up the carpet and found aluminum road signs siliconed to the rusted out floors.
 

72Burro

Jr. Member
Joined
Jan 5, 2004
Messages
51
Loc.
Ca
The po had manual windshield wiper set up. A spring was mounted in the cab w/ a pulley system and rope attached to the windsheild wipers. You pushed down w/ your left foot on a pedal that was installed to operate the windshield wipers.

Last, piece of chewed chewing gum was used to plug a hole in the rear end.. it actually worked
 

Awnrie69

Full Member
Joined
Oct 18, 2003
Messages
259
Loc.
Salem, Or
This is so mazing to me.... I never would have thought about using road signs to fix the floor boards... Wild stuff!
 

Ryans71

Sr. Member
Joined
Jun 24, 2001
Messages
786
Loc.
Milton, Wa
This is an old link, but I thought I'd share how the PO built the engine........one head was stock, the other had roller rockers.
 

Attachments

  • Old Engine 2.jpg
    Old Engine 2.jpg
    29.5 KB · Views: 87
  • Old Engine 1.jpg
    Old Engine 1.jpg
    28.8 KB · Views: 83

YelloTx73

Bronco Guru
Joined
May 13, 2004
Messages
1,419
Loc.
Katy/Galveston, TX
I found a pile of dirt covered in spray in bedliner in the corner next to one of my rear wheel wells. I cant wait to see what I find in the dash after reading about the rest of what you guys have found.
 

DuneBuster

Sr. Member
Joined
Dec 14, 2004
Messages
423
Loc.
Canton
Surprises

This is off track but the mention of floorboards reminded me of this Henry Ford Story.

In the early days of Ford, Henry started specifying the shipping containers for some parts from the suppllers, box size and design was specified, had to be of a certain type of wood, screws only, holes only at the ends of the wood strips, etc. The suppliers complained, but to no avail. When parts int ehse new shipping containers showed up, workers unscrewed the wood strips, others sanded them and painted them and once dry other workers put them on cars as running boards!! Henry got parts for his cars for free for some time, until the suppliers caught on...
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
my favorite- there were many p.o. monents there- was that the po broke the top of the coil spring off in the front, and then welded a box around the mount. the spring would stay on the bronco, but it flopped all over the place.
 

Bronco Sport

Bronco Guru
Joined
Jul 29, 2003
Messages
1,568
Loc.
NW Portland, Oregon
When replacing the lifters I learned that my 289 has 302 heads, I also just recently found out I had mustang door mirrors (no wonder they were so small)
 

Sac '68 sport

Bronco Guru
Joined
Apr 9, 2004
Messages
1,176
Loc.
Orangevale
How about a hitch made from 1/2 inch plate and bolted on using the bumper bolts. Not so bad you say, but probably not very strong. I guess he didn't think it would be that strong either so he then welded 1 inch angle iron from the back of the hitch to the 9" pumpkin.
It had long since been removed when I bought it, but still has the reminance of the angle iron welded on the top of the pumpkin. I bet that first drive was something else.
Lots of wire nuts, and an ammo container in the front passenger fender.
The ammo container was actually pretty usefull for storing extra oil and ps fluid though, just limited the travel on that side a little.
 

Eoth

Bronco Guru
Joined
Mar 10, 2004
Messages
1,692
I was totally clueless about what a EB should or shouldn't have when I bought my 1970, all I knew was that I bought a relatively "stock" Bronco.... Later I found out that the PO did the following:

All new wiring
swapped the 6 for a 302
Rebuilt trans
DANA 44s
disk brakes
power steering
4"lift

Probably the only time in my life when I got more than I bargained for :)
 

4x4x289

Sr. Member
Joined
Mar 15, 2004
Messages
966
67halfcab said:
My favorite PO upgrade was the road sign floors covered by Tin then the rubber floor mat.

Worst part was the road sign wasn't one piece but actually three.;D

was it a good road sign or did it have bullet holes? good road signs are hard to find. if they have bullet holes, you need to install them painted side up to minimize abrasion on the floor matt. ;D
 

Chief Master Sergeant

Retired U.S. Air Force
Joined
Nov 6, 2002
Messages
5,222
My previous EB, a 74, had some nice surprises. The PO had tried to patch some holes in the rear floor area. I knew it when I bought it and just thought he had done a bad job with silicone. Turned out he had cut beer cans up and siliconed the aluminum to the bed. It was a mess to get all that silicone up.
 

Mr Joe

Bronco Guru
Joined
Dec 2, 2003
Messages
2,212
When I got my EB, I thought it was amazing that it didn't have a lot of rust. Even the guys at the inspection station commented about how "solid" it was. Well, I started sanding the bed to prime and paint. I hit the front corners with the wire wheel and the PO had installed putty balls the size of softballs to cover large rot areas. I didn't notice them until they fell out of the bottom :eek:
The floor pans looked solid until I did some probing. He had laid down some undercoating followed by plastic sheeting followed by a hard putty material. The floor pans turned out to be swisscheese. %)

After reading about all these "fixes", I'd like to know how many of these were done by the present owners?? I know everyone here isn't a EB angel... ;)
 

Buckin74

Sr. Member
Joined
Aug 6, 2004
Messages
682
Loc.
San Diego
Mine is the usual rust story--- rocker panels rotted out so the PO just layered some reynolds wrap along the rockers and sealed them with fiberglass. He finished off with the leading edge of the floor boards with fiberglass to fill the holes.
I think he was an EX surfer !!!!!
 

4x4x289

Sr. Member
Joined
Mar 15, 2004
Messages
966
Mr Joe said:
After reading about all these "fixes", I'd like to know how many of these were done by the present owners?? I know everyone here isn't a EB angel... ;)

i admit i used road signs... tough material. i swear it was a last resort and that the body was beyond recovery. also, i've been known to lay the bondo on thick. my trick was to weld the seams, dent in the seams, bondo it, and then cut out the seams using a stanley knife. weld the seams to prevent blistering. cut the seams to control cracking. worked well. just had to do it in upper michigan, snow country.
 

67halfcab

Bronco Guru
Joined
Mar 30, 2002
Messages
1,642
Loc.
Michigan
4x4x289 said:
was it a good road sign or did it have bullet holes? good road signs are hard to find. if they have bullet holes, you need to install them painted side up to minimize abrasion on the floor matt. ;D


No they were not good, they had the typical "Drain" holes in them also. ;D
 

Grover

Full Member
Joined
Oct 10, 2003
Messages
223
Loc.
luhavull
My 76 has lots to still be uncovered, but here are few things that I have found so far. Extention cord wire run all under the indoor outdoor carpet I am guessing for the stereo. I had looked at the body pretty extensively because I have been burned on mustangs a couple of times. The entire underside was and still is covered with axel greese. I knew of this old trick to cover over rusted out spots, so I ran a magnet across most of it and seemed to be good. I pulled back the carpet on the drivers side all looked good I even pulled up some of the carpet in the rear by the tail gate looked good. I took a screw driver and tried to shove it through the floorpans in a couple of places and it never went through, good to go right. When I got it home I pulled up the carpet to find that the only good part of the floorboards were from the firewall to the the floor where the floor was replaced with sheet metal. The bed looks like swiss cheese the rear wheel tubs had rusted completely away from the bed but the PO had riveted in sheet metal then fiberglassed over that. I took out his rear inner quater panels to discover that the area had too been covered with axel greese. I don't think that I actually have any inner quaters, but he did fab up some type of fuel filler hose cover. The door post have metal under 1/2" of bondo along with the rocker panels. The quarter panels had been replaced but the seems are already rusted out and the work wasn't done correctly. There are holes in the top that are siliconed over. The 302 has been long replaced with a 351W which had supposedly been sitting since 98. The gas tanks were supposedly empty I found out when I removed the rear that it was full when it fell on my chest. I haven't been able to get the 351 fired up ever, I have to jump the sylenoid to try and start it up any way. I am sure that I have lots more to discover but I have yet to get all of the axel greese off of the bottom. I have used every kind of degreaser known to man along with a power washer and still haven't began to get half of the bronc cleaned. Oh well I love my PO and hope that he never works on cars again.
 

HotWheels

Bronco Guru
Joined
Jul 8, 2003
Messages
9,179
Loc.
Twilight Zone
I have a pic somewhere. When I got my 77 in Hawaii it had solid floors whioh I found interesing. When I was working on the exhaust..day 1..I found out why. DETOUR sings that you could read from underneath the vehicle. It was actually a smart move for Hawaii as rust is prevalent there. Nice job of inserting them also. Pop riveted and seam sealed verrrry well.

Galvanized patches attached everwhere else. Very creative I must say.
 
Top