• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Cracked block or bad install?

sigepkat

Full Member
Joined
Sep 23, 2004
Messages
281
I blew a head gasket a few months ago. I just recently finished the install of new gaskets. When I fired the truck up, I was still blowing white smoke from the left exhaust, but now I was also leaking antifreeze down that side of the motor. Does that sound more like I cracked the block or screwed up the basket install (put them in upside down maybe)?

Any thoughts are appreciated.
CM
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, I would re-torque the heads again. When I do a job like that I go over each bolt twice on the final torque setting to make sure I didn't skip any. Often the smoke from the exhaust is left over from before and will clear out. Be careful as it warms up so it doesn't overheat. Don't overfill it when cold or water will geyser out of the radiator. It will need more water once you reach operating temp. Hopefully you will be good. By the way cast iron head are are not prone to warping but aluminum head have a fair chance of warping if the motor overheated. If you need to take it apart again have the heads checked for flatness and make sure the head and block surfaces are perfectly clean. Good luck
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Find the coolant leak. I just went through a huge ordeal (4 sets of head gaskets) with what turned out to be a cracked head.

I found the crack after adding dye to the coolant and used a black light. I thought it was the block but nope......

Tim
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
Might possibly have put the gasket on backwards?
 
OP
OP
sigepkat

sigepkat

Full Member
Joined
Sep 23, 2004
Messages
281
Pulled the heads, gaskets are on correctly. Not sure of the brand and can't go look at the moment, I know they're not fel-pro...I had the heads checked prior to reinstalling, they're flat and not cracked...The block could be cracked, but short of pulling the motor, not sure how to check that...

CM
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I had my heads decked and checked too but one was still cracked internally and it didn't show up when magnafluxing them. The crack worked it's way to the outside the last time I installed the heads. I thought it was my block too when I had coolant running down the side of the block. Thought it was cracked at the bolt hole in the picture.

I added dye and used a black light to track the leak. Then was able to put 13 pounds of pressure on the system and the picture is what I found. I chipped the paint way so the crack could be seen.

Tim
 

Attachments

  • 20160825_084640.jpg
    20160825_084640.jpg
    90.7 KB · Views: 226

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
I've know several guys who have stopped head gasket leaks by retorquing them . Did you clean and lube the head bolts and clean the thread holes out before reinstall ?
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
When I fired the truck up, I was still blowing white smoke from the left exhaust, but now I was also leaking antifreeze down that side of the motor.
Does no one think this may be an intake manifold leak?

You need to find out (then let us know) exactly where the external leak starts.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
After re-torquing pressurize the cooling systems with a rental tool and see where you can see / hear it coming from. On a hot running engine it can be tough to see / hear anything. But 15 psi in the cooling system will help with push coolant out. If you get hissing in the PCV / oil fill / dip stick then it may be a leak into the block (crack). If a head gasket it could leak externally or into the chamber pull the spark plugs.
 
OP
OP
sigepkat

sigepkat

Full Member
Joined
Sep 23, 2004
Messages
281
I didn't "find" it, but I pulled the heads again and reinstalled them and that fixed the issue.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Chase the head bolt threads in the block and clean the holes well. Both mating surfaces should be spotless (block and heads)

I used ARP Ultra Torque lube on the threads and on both sides of the washers.

Check that your torque wrench is set correctly.

After putting on heads without a crack, I've had no further issues.

Tim
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Timmy390 - I read your thread on the cracked head and it made me so sad for you all that work over and over again.

Don't you need sealant on some of the bolt threads (those that go into the water jackets) and not just torque lube?
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Timmy390 - I read your thread on the cracked head and it made me so sad for you all that work over and over again.

Don't you need sealant on some of the bolt threads (those that go into the water jackets) and not just torque lube?

Thanks for the kind words. Don't feel sad for me.....it was just one of those things that sometimes happens. I posted all the info I could to maybe help a Bronco Brother in the future if they have issues. I did get a set of GT40P heads built for a song out of the deal.....

As for sealant.....my build was a 351W. Due to the W's taller deck height none of the head bolts go into the water jackets like on a 302. I double and triple checked mine due to all the "yes they do and not they don't" statements out there. Mine were as blind as the three mice so just lube was used.

Now I will say it's possible to have the bolt holes crack into the water jacket if the wrong bolts are put in i.e long bolts from the top installed in the bottom and tightened you could bust through. Also if someone runs the bolts down without the head on and bottoms them out.....

But in stock unabused form, my 96 roller bock had blind holes....

That said, you need to use sealant on the threads of a 302. I'm not sure if all of them go into the WJ or just the lowers.

Tim
 
Top