• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Cracked Block

elipryor

Jr. Member
Joined
Jan 12, 2009
Messages
64
Loc.
Cherryville
I am on the final stages of restoring my 74. I have 89 Mustang 5.0 in it. Got it all back together and started but saw I was getting antifreeze dripping from the back of the motor. Long story short the block is cracked. The motor only has about 500 miles on the rebuild and its running great so I hate to scrap it. Anybody had any luck fixing a cracked block. If so, how?
 

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
What a bummer! I know you can weld cast steel with nickel rod, but I have never heard of anyone welding on a block. The Aluminum block guys do it all the time. What do you have to loose?
 

Hors'nround

Full Member
Joined
Sep 4, 2007
Messages
230
Loc.
Spruce Grove Alberta
How do you know the block is cracked, have you already taken the engine apart?

If not, it could be the intake manifold to the head gasket, I had the same problem.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
How do you know the block is cracked, have you already taken the engine apart?

If not, it could be the intake manifold to the head gasket, I had the same problem.

I'm with Hors'n on this. Don't get excited until you know exactly where it's leaking.
 

Hoppy

Bronco Guru
Joined
Oct 29, 2007
Messages
1,193
Loc.
Gresham, OR
I hat e to say it
either way you do it you will have to pull the motor out
a 5.0 block is not all that hard to get
if you were doing a number matching restro then I could see trying to weld the block
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
How did you get a motor with only 500 miles on the rebuild? Maybe you found the reason.
If it is cracked, you could swap the good parts into another block. Most rebuilders final fit the pistons to the hole with a hone anyway.
 

Ryan

Sr. Member
Joined
Aug 29, 2003
Messages
739
Loc.
Lansing, MI
drill
tap
plug
repeat

do a search, its common for people with rare blocks to do it. but not for something like a 5.0L, get a new block
 

Knox

New Member
Joined
Jul 17, 2006
Messages
33
Liquid glass

Sodium silicate can be used to seal leaks at the head gasket. A common use is when an alloy cylinder head engine is left sitting for extended periods or the coolant is not changed at proper intervals, electrolysis can "eat out" sections of the head causing the gasket to fail.

Rather than remove the cylinder head, "liquid glass" is poured into the radiator and allowed to circulate. The waterglass is injected via the radiator water into the hotspot at the engine. This technique works because at 210–220 °F the sodium silicate loses water molecules to form a very powerful sealant that will not re-melt below 1500 °F.

A sodium silicate repair of a leaking head gasket can hold for up to two years and even longer in some cases. The effect will be almost instant, and steam from the radiator water will stop coming out the exhaust within minutes of application. This repair only works with water-to-cylinder or water-to-air applications and where the sodium silicate reaches the "conversion" temperature of 210–220 °F.
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
What are the cons to that stuff ? It seems like it would have some nasty side effects on other parts ....
 

RajinCajun

Bronco Guru
Joined
Nov 22, 2003
Messages
1,587
Loc.
HawleyTX, La orig.
Liquid glass

Sodium silicate can be used to seal leaks at the head gasket. .

Last resort for a quick fix until you can get time or $ to pull the engine. I have seen the aftermath of it, usually over heats due to radiator being plugged, and warps heads... Just my $.02.
 
OP
OP
E

elipryor

Jr. Member
Joined
Jan 12, 2009
Messages
64
Loc.
Cherryville
Thanks guys, drilled out both sides of crack to keep it from going any further then ground it out a little. Cleaned, heated, cleaned, heated, cleaned, and cleaned. JB welded, and then covered with body filler. Local mechanic said he seen a old ford tractor work like this for years. May have been a waste of time but it is working right now. I did not have anything to loose. Probably look for new block while it is being painted.
 

4G5

Full Member
Joined
Oct 7, 2009
Messages
240
Loc.
Newport News,VA
My father used to weld on cast marine blocks all the time when I was younger. I do know that you have to use nickel rod but am not sure about the actual settings for it. If you are not so sure about your own welding skills (no offense intended) I would def. take it somewhere. I personally am not very good at welding cast but my father is, but I guess the simple fact that he is a Master Nuclear Welder helps too.

Best of luck! Let us know how it comes out.
 
Top