• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dan Wheeler's Astro Hydroboost Thread

OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
this pic shows the passenger side going to the pump

776448793_CCyZ7-S.jpg
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Hey Dan,

I have been following Nightstick's thread, which pointed to yours.

I am confused by a couple of things...

1. I have an existing power steering pump (probably from a late Early Bronco). I bought a rebuilt Saginaw to replace it with during the Hydroboost project. Do I need a different pulley, or can I reuse the original? (I hope that isn't a stupid question to ask.)

2. The Bronco has a manual brake system. Do I need to use a different master cylinder and reservoir, or can I use what I have? (I also saw your statement about a new proportioning valve.)

Thanks for any advice you can offer.

Jeff
 

larryejoh

Full Member
Joined
Feb 12, 2006
Messages
201
I went the cheap route and used Astrovan hoses. I cut the ends off on the pump end and box ends and used the original Ford fittings on the lines and then flared the end of the lines.
 

Nightstick

Bronco guy
Joined
Feb 6, 2010
Messages
2,929
1. You're gonna have to find out what the pulley shaft diameter is. A sag pump is 0.75", WH says a stock bronco is 0.69" so it doesn't look like you'll be able to use the same pulley.

2. Not 100% sure on this, but you need to match the MC with whatever brake system you have i.e. Drum/drum, drum/disc, etc. A prop valve allows you to adjust the braking power, but I've only heard of them being used with disc brake setups. It would be worth it to go to a front disc setup. If you have the astro MC you can use that or get a 79 camaro MC for $30 from the parts store and throw it on there.
 
OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
Hey Dan,

I have been following Nightstick's thread, which pointed to yours.

I am confused by a couple of things...

1. I have an existing power steering pump (probably from a late Early Bronco). I bought a rebuilt Saginaw to replace it with during the Hydroboost project. Do I need a different pulley, or can I reuse the original? (I hope that isn't a stupid question to ask.)

2. The Bronco has a manual brake system. Do I need to use a different master cylinder and reservoir, or can I use what I have? (I also saw your statement about a new proportioning valve.)

Thanks for any advice you can offer.

Jeff

If you're not changing the brakes themselves (to disc) and nothing beyond the master cylinder has or will be changing, then there is no reason to change the master cylinder as long as it fits on the h-boost unit. The hydroboost simply applies pressure to the master cylinder so your foot doesn't have to.

I'm not sure on the pulley. My guess is that if you can transfer it over and it fits then it will probably be fine.
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Nightstick and Dan,

Thanks for your replies.

The Bronco is a 1971. I bought it with disc brakes already installed on all 4 wheels. I would like to think that means that the master cylinder is correct, which from what you have said would mean that I wouldn't need to replace it. Not everything has been done right on this Bronco, so I don't want to assume anything.

Any thoughts on how I could make sure the master cylinder is right for the current set-up?

Thanks for both of your posts, and for your write-ups. It sure makes it easier to do this work with excellent information.

Thanks

Jeff
 

Nightstick

Bronco guy
Joined
Feb 6, 2010
Messages
2,929
I don't know how you could verify whether or not you have the correct MC unless you can figure out exactly what vehicle it came off of. No bronco came from the factory with four wheel disc so that might help a little. You're also gonna need the correct bore size to match the astroboost unit. IMO the easiest thing to do would be to replace it with one you know is correct.
 
OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
like i said, if it brakes OK now and you aren't changing the brake system, then you shouldn't need to change the M/C. The h-boost is just doing the pushing for your foot.

There's no need to match bore size of the M/C with the h-boost unit. Bore size matching of the M/C is done between the M/C and the caliper pistons on the brakes.

you *might* need to match the throw of the h-boost to the M/C but I doubt it.

I just switched to disc/disc recently and used an old Corvette M/C which seems to work OK. It was kinda pricey though. I think there are other options for disc/disc Chevy M/Cs.
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Hey,

Thanks again for the input.

I measured the shafts, and like was posted by another member (one of you guys, maybe), the shaft on the stock pump is slightly less than .70". The shaft on the Saginaw is .75".

More trips to NAPA and AutoZone for a new pulley and a pulley installer.

I am hoping my auto shopping runs are over for the weekend. If I get everything installed with the exception of the high pressure hoses, I will probably have them made at NAPA on Monday unless it is a lot less expensive to do it myself.

I didn't want to get started and then need to make more runs... I sure hope I'm good to go.

Thanks again.

Jeff
 
OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
Hey,

Thanks again for the input.

I measured the shafts, and like was posted by another member (one of you guys, maybe), the shaft on the stock pump is slightly less than .70". The shaft on the Saginaw is .75".

More trips to NAPA and AutoZone for a new pulley and a pulley installer.

I am hoping my auto shopping runs are over for the weekend. If I get everything installed with the exception of the high pressure hoses, I will probably have them made at NAPA on Monday unless it is a lot less expensive to do it myself.

I didn't want to get started and then need to make more runs... I sure hope I'm good to go.

Thanks again.

Jeff

Do you have the fittings for the h-boost input and output? they are metric bubble flare and NAPA may not be able to make hoses that work with metric bubble flare. There should be a parts list on page 1 of this thread that lists the fittings you need to convert to AN. But then NAPA may not be able to make AN hoses - they probably just make inverted flare hoses.
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Hi Dan,

Thanks for your input. I know that what you are saying may be true.... I waited too long to start this project, and with putting the Bronco in a shop to get the caster corrected next week, and being out of town for a few days, I knew I was running out of time for getting the Bronco for a run in a week.

I am thinking that if I can get the set-up installed before taking it to the shop next week, it wouldn't have power steering or brakes; but, it could be driven off the trailer and into their shop. Not the best option; but, if I can't get hoses made locally, I will order the fittings on Monday and make up the hoses on Friday when I get back in town and pick up the Bronco.

I'll keep you posted.

Thanks

Jeff
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Hey Dan,

I was getting my information together to question NAPA. I was looking at the parts links you have in the first post.

The following part, http://api.viglink.com/api/click?fo...=RUS-648060 &jsonp=vglnk_jsonp_13134055447373

is identified as being aluminum on Summit. Your post indicates stainless steel. If it is aluminum, is there anything to be concerned about with either strength or compatibility with the power steering fluid?

Thanks

Jeff
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Dan,

Sorry for another question...

I bought the 1978 Lincoln power steering pump remanufactured by NAPA. There isn't much good info in the specs. I checked the corresponding hose for that year Lincoln from the pump to the hydroboost unit.

This is where I am getting confused. One end of the hose has a 7/16" F Inv. Flare and the other end has a 7/16 M O-Ring. Does one of these look right to you?

Jeff
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
You Were Right

Hi Dan,

Do you have the fittings for the h-boost input and output? they are metric bubble flare and NAPA may not be able to make hoses that work with metric bubble flare. There should be a parts list on page 1 of this thread that lists the fittings you need to convert to AN. But then NAPA may not be able to make AN hoses - they probably just make inverted flare hoses.

In spite of the information I was given, NAPA's hose guy was not able to make the hoses for me... Another lessor learned.

Thanks again.

Jeff
 
OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
Hmm sorry Jeff, I'm a little out of my element now... I've only done one of these boost setups so I only know how mine works. I thought the Saginaw canned ham pumps were either 16mm bubble flare or 3/8ths inverted flare for the output. My Saginaw (when I had it) was 3/8ths inverted flare. I used a fitting to convert the output to -6an.

7/16ths sounds more like the steering gearbox IIRC. Should be listed on page 1. I would recommend using fittings to convert all your high pressure inputs and outputs to -6an then make your own hoses with the Russell powerflex stuff which is specific for power steering and rated to 2000psi. PM me if you have any more questions then we can switch to email.
 

Jeff10

Contributor
Bronco Guru
Joined
Feb 20, 2011
Messages
2,182
Loc.
Indianapolis
Hi Dan,

Hmm sorry Jeff, I'm a little out of my element now... I've only done one of these boost setups so I only know how mine works. I thought the Saginaw canned ham pumps were either 16mm bubble flare or 3/8ths inverted flare for the output. My Saginaw (when I had it) was 3/8ths inverted flare. I used a fitting to convert the output to -6an.

7/16ths sounds more like the steering gearbox IIRC. Should be listed on page 1. I would recommend using fittings to convert all your high pressure inputs and outputs to -6an then make your own hoses with the Russell powerflex stuff which is specific for power steering and rated to 2000psi. PM me if you have any more questions then we can switch to email.

No need to apologize. I'm not being critical. I just want to make sure I know what's going on. Nothing on this project has been easy.

You are right about the fitting. It's kind of a long story; but, I bought a fitting and tuble from NAPA intented to be used to make up to a hose. By cross-referencing and checking the part with what it was intended to mate to, I know it was 3/8, and I believe it is an inveted flare, although I need to make sure of the style. I know the nut fits, and I believe the seal of the inverted flair fits nicely.

I'll be ordering the parts tomorrow, just so I have time to make sure they are correct.

If I have any more questions this evening, I will PM you. Thanks for the offer. Your write-up, and Nightstick's have helped a lot. There is so much variation between what is being used that it is tough to say for certain. It's surely not like the 2 year old JK I recently sold.

Thanks

Jeff
 

Mark

Contributor
Bronco Klutz
Joined
Aug 29, 2003
Messages
5,417
Loc.
NW Indiana
Just to muddy the waters a little bit.. I just checked the pressure fitting size on my 4x4x2 box... Its 1/2-20 inverted flare...so I guess some are different.. Check yours before ordering

Mine is the same way! Pressure port 1/2-20. screwed me up and crossed my lines
 

hammer

Bronco Guru
Joined
Nov 13, 2006
Messages
1,359
Hey guys, im just trucking through this right now. Just installed the RUS-648060 fitting into the hydroboost unit. It doesn't seat in all the way. There are threads exposed on the lower side of the fitting. Looks as though Dan's might be the same way, judging by the pic in his first post.

277020266_h733C-S.jpg


Here's mine;

425020_334628076567530_100000610208884_1080557_1582283104_n.jpg


Is this fine? Dan any issues with yours?

Here is the stock Astro fitting vs the RUS-648060

422421_334647496565588_100000610208884_1080566_1420510382_n.jpg
 

hammer

Bronco Guru
Joined
Nov 13, 2006
Messages
1,359
Also is there any resolution to which way the "T" should be run? I think 3 different people have listed 3 different ways to hook it up in this thread. Hmm maybe this calls for a poll thread.;D
 
OP
OP
DanWheeler

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
here's a pic of mine. I'd say it looks pretty similar to yours. it looks like one of the fittings sits lower than the other.

WP0005331-M.jpg
 
Top