• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EEC IV Engine Sputtering- TFI question?

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
Ok, there are a lot of unknowns still, but I do want to check something. This past race, the 302 sputtered on acceleration from a stop. It was popping back through the intake and lacked power at full throttle. Idled fine and nursed it through to a finish.

I figured it was a fuel issue (as it ran fine the first few races). I checked the fuel filter, and it had some crap in it, but not a ton. I thought maybe the fuel cell foam was breaking down. I will check fuel pressure today.

A buddy sent me this info:

"i had a similar issue with the engine popping and such...i found a wire(think it was purple) that went to the TFI and it had 12v when it wasnt suppose to. so we cut it (per thread on classic) and now it revs til cows come home...before it would spit and sputter round 3k or more. as a matter of fact, i think i swap fuel pumps thinking it was starving...but that wire fixed it"

I searched- so don't trash me too bad, but can anyone throw me a link to that thread?? I couldn't find it.
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
Ok, there are a lot of unknowns still, but I do want to check something. This past race, the 302 sputtered on acceleration from a stop. It was popping back through the intake and lacked power at full throttle. Idled fine and nursed it through to a finish.

I figured it was a fuel issue (as it ran fine the first few races). I checked the fuel filter, and it had some crap in it, but not a ton. I thought maybe the fuel cell foam was breaking down. I will check fuel pressure today.

A buddy sent me this info:

"i had a similar issue with the engine popping and such...i found a wire(think it was purple) that went to the TFI and it had 12v when it wasnt suppose to. so we cut it (per thread on classic) and now it revs til cows come home...before it would spit and sputter round 3k or more. as a matter of fact, i think i swap fuel pumps thinking it was starving...but that wire fixed it"

I searched- so don't trash me too bad, but can anyone throw me a link to that thread?? I couldn't find it.

pins 3 & 4 on the TFi connector one should have +12 in run and the other +12v in start only, not sure which is which but 12 on both is bad..

but if your stuff worked at one time then starting acting up then I would suspect something else..

check for junk in the fuel lines..I had junk once cleaned it out .. happened again found more junk...so clean them out real good..
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Nice build thread.

The TFI issue is when constant 12V is put to pin #3. It should only see 12v in START. Something to look at though.

Also clean the MAF. You can disconnect the MAF and see if it runs better.That will point to a possible problem with it.
 

Attachments

  • tfi wiring.JPG
    tfi wiring.JPG
    55 KB · Views: 21

dbevans2249

Sr. Member
Joined
Sep 21, 2003
Messages
610
Loc.
Buena Park, Ca.
I read your awesom build thread. Wow!!
Just a thought. IIRC you installed a new KN Air Filter before the problem started. Could it have gotten oil on the MAF? IIRC that is why many on here use dry type filters.
 
OP
OP
broncosbybart

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
thanks all. any suggestions on cleaning the MAF? i don't want to hurt it using compressed air or using a cleaner/solvent that might harm it. it very likely has a good coating of dust on it after this last race. the old air filter had a healthy coating of dust on the inside of it. the K&N isn't installed yet. the engine has been run with a dry type filter thus far.
 

dbevans2249

Sr. Member
Joined
Sep 21, 2003
Messages
610
Loc.
Buena Park, Ca.
I read about cleaning it not long ago. IIRC it was on a Mustang Forum. I don’t remember which one but it may Goggle. Some of the members here with more knowledge may have something to add.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
There is a specific MAF spray cleaner at the parts stores. I wouldn't use high pressure air. I have used brake cleaner in the past.
 
OP
OP
broncosbybart

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
ok. i will try cleaning the MAF. i checked fuel pressure. it is at 30 lbs, regardless of throttle position. might be kind of low, but it has been there since the build. it still pops out the intake. the MAF does have a pretty good amount of dust in it.
 
OP
OP
broncosbybart

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
Cleaned the MAF and TB. Seems to run like a champ once again! Will know better tomorrow, after a day of wheeling. Thanks guys!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That pressure is awful low for a Ford engine I would think. Especially a race engine.
It's certainly enough to run the engine from, but at closer to 40 psi, your 30 is 25% low.

Seems a lot to me, so might at least keep that in mind as something to investigate in the future. Can't argue with a good running engine, but if it's causing it to be overly sensitive to other maladies, it'd be worth fixing.

Paul
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
ok. i will try cleaning the MAF. i checked fuel pressure. it is at 30 lbs, regardless of throttle position. might be kind of low, but it has been there since the build. it still pops out the intake. the MAF does have a pretty good amount of dust in it.

at idle 30psi is probably Ok disconnect the vacuum from the fuel regulator you should see 40 psi .
 
Top