• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fitech installed and running.....WOW!

jasonv

Sr. Member
Joined
Jan 7, 2002
Messages
355
Well I got my christmas present installed and running, the Go Street 400HP kit. I am shocked at how nice it is. :cool:;D:eek: Zoom Zoom, the rebuild is purring like a kitten. Anybody want to buy a carburetor? It only took a day or so to actually install after a two weeks of gathering parts and planning. Thanks to everyone on here for help in the planning. I am running a frame mounted fuel pump connected to just the stock 12 gal tank, the aux tank has been abandoned in place. Hopefully I'll be getting a 23 gallon here in the future (and headers). I ran a new line down the passenger side of the frame for the return line and tied it into the main tank vent line. Only issue there is the vent line is 5/8 and I have -6an hose (3/8) so finding a tee was impossible. I ended up using a 1/2x1/2x3/8 tee and just cinching down the hose clamps. No leaks in the first test starts and drive. only other hiccup is the air cleaner stud is a different size!!! off to Napa again....

So do I need to think about any tuning issues or just let it do its thing? It's a daily driver.

Jason
 

Dlish

Sr. Member
Joined
Dec 6, 2011
Messages
552
Excellent to read your experience. I have my FI Tech still in the box, just haven't picked up new lines and a pump yet.
 

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
If you think it's running well just let it tune itself. If you have any issues like backfires or hot/cold starting problems then dig into some of the adjustments that can be made. If she's running nice like you say then I would just put some miles on it.
 

RADO

Jr. Member
Joined
Sep 26, 2016
Messages
138
Loc.
Phoenix
Like Cortez stated, just drive the Bronco and the Fitech will dial in the fine adjustments for you. I made the mistake of trying to tune the Fitech before driving it much and made a mess of set points. Once I decided to leave it alone, the Fitech started working out the little issues on it's own. Eventually, I did make some adjustments myself, but only after I really understood what I was trying to improve.

I just drove my Bronco 900 miles to AZ and the Fitech performed great the entire way.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Jasonv - Good to hear more great reviews.

I also just did a FiTech (400 Go Street) install on a Jeep Grand Wagoneer with a 360. Just like the early Bronco, it has the original Duraspark II so, very similar install.

It runs great with no issues and continues to run better with each drive.

I also have a FiTech 600 with Timing Control waiting for my 69 Bronco to get back from Body Shop. It should be up and running in a couple weeks.
 

Jp76

Jr. Member
Joined
Sep 4, 2017
Messages
67
Loc.
Cave Creek, AZ
Not to Hi-Jack the convo, but I have been running fuel line and return, etc. on my 76 to prep for the Fitech install. I have a Sherman 23 gallon tank with in-tank elec pump. Question for the experts - I have a single wire Distributor with a 6AL MSD box and Blaster2 Coil (already installed when I bought the Bronk). Do I need to do anything special to hook everything up? Also, are plugs and gapping any different after install? I am really looking forward to getting her back on the road. Thanks All!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Single wire distributor should be a breaker point ignition.
That being hooked up to an MSD is a viable option, they do work that way.
There should be a tach terminal on the MSD box, follow the instructions with the EFI on how to connect to the tach terminal on an MSD box. That will be what you want to use.
Plug gap should be set to typical elelctronic ignition gap for your engine. I would guess the .040~.046" range as a starting point.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If you're going to run the FiTech 400 series it won't matter what distributor you use.
If you're planning to use the 600 series, but not use it to control the ignition timing, it won't matter what distributor you use.
Just follow what 'bowsher said about the tach signal.

If you want the new EFI computer to control the timing however, a single wire distributor (points, or Pertronix Ignitor for example) won't cut it and you will need to change it out to a 2-wire trigger type distributor.

Paul
 
OP
OP
J

jasonv

Sr. Member
Joined
Jan 7, 2002
Messages
355
I have a 6A box and the Fitech connects to the gray tach wire from the 6A. Obviously no Fitech timing functions on my setup.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Good info on the 6A and MSD distributors. I plan to add FiTech to my 69 Mach 1 390 car and have a full MSD setup.

Tim
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I'm running my 600PA setup like that and not using the built in timing feature - works great, hence I haven't switched over to it yet.
 
Top