• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Full width swap

399strokerEB

Contributor
Bronco Guru
Joined
Jun 23, 2010
Messages
1,733
Loc.
Wasilla, AK
I know there are quit a few of these threads, but I'm having an issue locating a build thread that goes through step by step. I started gathering parts for my full width swap. Axles are 1/2 ton out of a 77 150, and I will be building some Lars bars as well. Currently running a 4.5" and 2" body lift but the front sits higher so I'm hoping this helps out with the HP clearances. I've done atleast a dozen searches in both the chat and tech sections and not finding what I'm looking for. Thanks guys ;D
 

Waverous

Contributor
Bronco Guru
Joined
Oct 5, 2001
Messages
2,766
Loc.
Aurora, CO
Last time I added full-width axles under a Bronco, generally speaking, I had the frame supported at the horns so I could get the axles* under the frame and centered. I did this to locate spring mounts, shock mounts, driveline angles, trackbars, tie rods, etc.. Once I had axles placed and attached to the frame, I mounted the tires and wheels I planned to use and then placed the tub over the body to check for clearance issues with the intended lift I was going use.

*Personally, I would build axles before placing them under the frame - your choice though

This a VERY general overview, but I think it is a good outline for a plan to start
 

bronco217

Jr. Member
Joined
Nov 13, 2003
Messages
117
I just put a '77 HP in mine and got some pointers for you. I have 5.5" coils in mine and with 7 degree bushings it puts the pinion at the perfect angle for the drive shaft, however, it has terrible castor. if I was to do it again I would cut both sets of wedges off and the inner C's, mock it up with 0 degree bushings, give it 6-8 degrees negative castor, put the pinion in good position, and burn it in. My winter project is to knock the inner C's off and fix my castor. It's a good axle to use since you can knock off the wedges.
Tom
 

78Scronco

Bronco Guru
Joined
Nov 2, 2005
Messages
1,282
I did mine, what info you need? Its really not all that different than adding a suspension lift to your bronco. Mine has 3.5" suspension and 2" body. If I remember correct, I have 4 degree C-Bushings. with a 78 HP dana 44 front.

Changes off the top of my head are:
rear:
1. Re-locate the rear leaf spring perches closer in.
2. new shock mount location on the axle.

Front:
1. different degree C-bushings
2. Adjustable Trac Bar
 
OP
OP
399strokerEB

399strokerEB

Contributor
Bronco Guru
Joined
Jun 23, 2010
Messages
1,733
Loc.
Wasilla, AK
Thanks guys, COSCAG00 I actually pulled the pictures out of your thread as a reference for when I start ;D. 78Scronco are you having any clearance issues with that small of a lift?
 

COSCAG00

Sr. Member
Joined
May 16, 2011
Messages
426
I did mine, what info you need? Its really not all that different than adding a suspension lift to your bronco. Mine has 3.5" suspension and 2" body. If I remember correct, I have 4 degree C-Bushings. with a 78 HP dana 44 front.

Changes off the top of my head are:
rear:
1. Re-locate the rear leaf spring perches closer in.
2. new shock mount location on the axle.

Front:
1. different degree C-bushings
2. Adjustable Trac Bar

I have the exact set up.
 

mortimersnerd

Sr. Member
Joined
Aug 25, 2010
Messages
743
Some more detail about exactly what you're looking for would help. I'd cut off the C's, set the pinion angle and then move them inboard to match the stock locations. Reweld (or better yet, install new ones) and bolt everything back in place. It's also a good chance to extend the wheelbase if you want to. You'll need to figure out the track bar bracket, but if you keep the stock C's that'll be done for you as well. Alternately, ditch the C's and gain some flex with some tube based radius arms using these brackets: http://www.ballisticfabrication.com/Flat-Bottom-Radius-Arm-Coil-Mounts_p_1184.html. Or do what I'm doing and convert to coilovers.
 
OP
OP
399strokerEB

399strokerEB

Contributor
Bronco Guru
Joined
Jun 23, 2010
Messages
1,733
Loc.
Wasilla, AK
Basically I'm looking for a detailed build thread of someones swap, preferably with Lars bars. I'm probably going to get the duffs coil brackets so I dont have to mess with trying to get the pinion angle correct(a little hard to do on an uneven gravel driveway).
 
Top