I'm not expert but wouldn't getting a drop radius arm bracket get you the caster you need? The WildHorse kit looks very nice. Not sure what all the other vender sell.
http://www.wildhorses4x4.com/product/Adjustable_Drop_Strut_Arm_Brac/h
If it were me, I would do the radius arm drop before I cut and turned anything.
Tim
Dropping the radius arms will add more caster. Anything that rotates the axle will change the caster.
The problem is the U-joint at the front axle. With 7° bushings alone you are very close to maxing out the operating angle of the U-joint. More caster means a steeper operating angle. It is all due to rotating the housing. Cutting and turning the C's lets you straighten out the U-joint angle into something that is managable and dial in the Caster seperatly.
Now a 7° bushing should make a 7° change. But that has proven to not always be the case. Don't know where the tolerance adds in at but there are a few degrees of error that can happen wiht the bushings.
Also the cutting the Cs off isn't just a pure cut. they are pressed into the axle tubes and welded. What you really want to do is cut the weld. Free up the C to rotate in the tube. Then weld it back at the new rotated angle. Doing a full cut will remove the inner structure of the C where it fits into the tube compromising the strength. It is spelled out in the instruction threads. Just wanted to make sure you realized that before just blindly cutting.
Not sure if you really want 10° of caster. Ususally 5-7 is the target. I think the highest I have heard of is 9°.
On a slightly diffrent tangent, rear suspension.
The shortish rear springs and adding a soft all spring lift to an early bronco has an interesting thing happen to the rear suspension that makes for a little squirrliness at highway speeds and curves. I noticed it most on I17 taking the fast sweepers heading into Phoenix.
With the axle mounted low and the front spring mounts high on the frame you get more pronounced roll steer. Think of the spring as a suspension link, and it is. The front part is what dictates the arc the axle housing moves as the spring cycles. The rear is free to float on the shackle. With a high arc spring the angle of the link is steep. As it compresses it pushes that side of the axle back. Extension pulls it forward. Add in the narrow chassis and it is even more pronounced.
So what is happening? Lets take a sweeping right turn (same happens in left but once you figure the right you can reverse for the other direction). You go into the turn and steer a little to the right. Vehicle reacts, you get a little body roll. The outside rear tire (left side) arcs back a tiny amount and the inside tire (right side) arcs forward a little. This steers the rear axle a little and makes the Bronco turn right. But you already are steering to the right with the front axle. You are getting more right hand yaw then desired. So you straighten out the turn. This unloads the body roll, the rear axle straightens out, now you just lost both the front and rear steer. But the road is still turning right. So you steer back into it. Everything repeats. You find yourself sawing the steering while in a turn. Often thoughts are the steering is too fast and you can't get the angle you really want. That is partially true, the desired angle is more difficult to reach. A slower steering box will more gradually load and unload the chassis (and body roll) in the turn and give you a better chance at finding a happy spot in the middle. If you could eliminate the roll steer (or even better reverse the direction of the roll steer) it will make sweeping highway curves feel like you are taking them in a much longer wheelbase vehicle.
This is one area where a flatter spring and blocks actually help. Yes, evil lift blocks can be good as strange as it sounds. If you look at most trucks you will see the front spring mount is fairly low, often below the bottom of the frame. It is often a straight shot to the axle housing, sometimes even with a slight rise to the axle mounting point. The arc then goes up and the shackle mount is almost touching the bed. This is for roll steer. You get an F350 and it has factory lift blocks. Not because they were cheap and used the same springs (which they have been known to do), but to get the extra height and keep the correct spring geometery for the roll steer. They didn't have to change the spring perch locations.
Oh the joys of suspension. There are 2 or 3 good chassis books I could refer you to if you really wanted to get deeper into this (and I only scratched the surface here).
http://www.addco.net/aftermarket/tech/handling-book/ is a nice little starting point. I got a printed copy at SEMA a few years ago and have found it a great simple reference. Looks like the online version is still the same 2005 that I have. I will have to find the books at work for the fancy formulas. I have not seen them in a while, I hope they have not walked away. They were expensive books.