• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

more steering resistance

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
How can i get more resistance in the steering. it steers good but it is touchy. i dont want it harder to turn just less touchy when driving. i have a delphi box and stabilizer.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
The short wheel base and quick ratio box makes it touchy as well as lack of caster. Besides putting in more caster. Not real sure there is much else you can do. Short of swapping to a 6 turn box. About the only other thing that could be done is find a way to lower the pressure coming out of the pump but then low speed turns would suffer.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Lots of caster will help. If you can get +5 to 7° when finished it will want to track straight and add effort when turning.

There are other factors that can get deep into theory and multi-step cause/effect sceneros as well.
Do you have a sway bar(s)?
How much lift do you have?
How is the REAR lifted?
Just checking, what suspension are you running (any 3-link, etc.)
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
ok stupid question. what is gained by swaping to a quick steer box? other than less turns lock to lock. when i swapped the box i went from a worn out stock power steering to the delphi quick box. would i have been better to to stay stock? im mainly on pavment. im compairing the steering resistance to my 01 3500 maybe thats not a fair comparision.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
i think im +2 on caster. thats what the line up guy told me. ive got the 6.25° bushings from duffs , No sway bars, 3.5" sus. 2" body. 11 leaf in rear. no three link. To get more caster would wristing the axle be next. i really want this thing to drive good. its ok now but if your on a two lane road and meet another car you hold you breath and dont wiggle.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I run the delphi box and my steering is so good, I removed the stabilizer I'd been running with a worn out stock. Becasue of that I'm going to say it's not the box. BTY I'm running 7 degree bushings with my 2.5 lift. Set the toe myself and it tracks and steers like a dream. I do have all new steering parts........

its ok now but if your on a two lane road and meet another car you hold you breath and dont wiggle.

Man, I hate to tell you but that's NOT GOOD......if you have to hold you breath and don't wiggle when meeting other cars, then you have more going on than needing more caster.

What are the drag link and track bar angles like? You running a drop pitman arm, track bar riser/drop bracket? Do you have an adjustable drag link? How old are the track bar bushings? Ball joints and tie rods how old are they? Are the C bushings in correctly?

BTY, I have family in McDonald.......I know Cleveland well.....

Tim
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
maybe not holding my breath but on a narrow road you have to be paying attention. heres a picture of the underside. all bushings and stuff are new with in the last year. it will not reurn to center say after pulling out onto the road. you have to steer it back straight. ive been researching wristing the axle to gain more caster.
 

Attachments

  • bronco steering.jpg
    bronco steering.jpg
    73.4 KB · Views: 123

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Pretty much lack of caster is your main issue. Wristing does not gain caster. you pretty much need to cut the C's off and rotate them. Then you can also maintain proper pinion angle as well. Longer radius arms can help a little as well.
quick ratio boxes are basically what you said quicker turning so they tend to be more touchy when other things are not ideal. Even with a 6 turn box if your caster is bad it will still be a little touchy. But it is slower acting so they are not as touchy.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
if you were going to cut the C's and rotate them how much would you go. here is a pic of my front drive angle. can i keep the 7 bushings or would i need to go to a 2 or 4 ?
 

Attachments

  • drive shaft angle.jpg
    drive shaft angle.jpg
    55.9 KB · Views: 79
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
i have went back and read a post i had about a year ago about rotating the C's. so just to make sure the C's are the very end of the axle where the king pins are? not where the c bushings go? dang i can get this in my head.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
right the C's are where the kingpin/ball joints go. You could cut the wedges off and move them but you wont gain any pinion angle. Bascially I'd go back to 0 or 2 degree bushings then set your C's to get 4-7 degrees. That way you still have other bushing availible to you if you ever need more.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
im going to take it back to lineup shop tomorrow and double check what i have now. i think its +2 degress. so if i took the 7 degree out and went to 0 bushings i would be at
-5 so i would need to rotate the c's 15 degress to be at +10.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
Tim, would the drop brackets increase the drive shaft angle? I can get the work done for about 150-200. in chattanooga. im wanting to be able to drive it to townsend in a few months.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Not sure I'd rotate that far. I shoot for no more than 7-8 degrees max with the bushings. As Tim said radius arm drop brackets are a option as well just a lot of people that offroad a lot shy away from them due to ground clearance issues.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Tim, would the drop brackets increase the drive shaft angle?

Yes it will. Putting the lift on rotates the housing up, the drop arms will rotate it back down. The WH kit looks like it gives you three angles/drops to choose from where as other brackest I've seen have only one.

I would get the numbers from the alignment shop and tehn give Wh a call and see if the kit is the goldon ticket.......

Then again, getting the "C's cut, turned and welded for 200 don't seem bad....but you lock yourself in once you do that. No easy way to go back....if you ever did want to.

Tim
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Also consider that the drop brackets may allow you to go with less degree bushings which will rotate the pinon to a angle closer to stock. Overall moving the C's is a better choice. Just takes more work than the drop brackets.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I'm not expert but wouldn't getting a drop radius arm bracket get you the caster you need? The WildHorse kit looks very nice. Not sure what all the other vender sell.

http://www.wildhorses4x4.com/product/Adjustable_Drop_Strut_Arm_Brac/h

If it were me, I would do the radius arm drop before I cut and turned anything.

Tim

Dropping the radius arms will add more caster. Anything that rotates the axle will change the caster.

The problem is the U-joint at the front axle. With 7° bushings alone you are very close to maxing out the operating angle of the U-joint. More caster means a steeper operating angle. It is all due to rotating the housing. Cutting and turning the C's lets you straighten out the U-joint angle into something that is managable and dial in the Caster seperatly.

Now a 7° bushing should make a 7° change. But that has proven to not always be the case. Don't know where the tolerance adds in at but there are a few degrees of error that can happen wiht the bushings.

Also the cutting the Cs off isn't just a pure cut. they are pressed into the axle tubes and welded. What you really want to do is cut the weld. Free up the C to rotate in the tube. Then weld it back at the new rotated angle. Doing a full cut will remove the inner structure of the C where it fits into the tube compromising the strength. It is spelled out in the instruction threads. Just wanted to make sure you realized that before just blindly cutting.

Not sure if you really want 10° of caster. Ususally 5-7 is the target. I think the highest I have heard of is 9°.



On a slightly diffrent tangent, rear suspension.
The shortish rear springs and adding a soft all spring lift to an early bronco has an interesting thing happen to the rear suspension that makes for a little squirrliness at highway speeds and curves. I noticed it most on I17 taking the fast sweepers heading into Phoenix.
With the axle mounted low and the front spring mounts high on the frame you get more pronounced roll steer. Think of the spring as a suspension link, and it is. The front part is what dictates the arc the axle housing moves as the spring cycles. The rear is free to float on the shackle. With a high arc spring the angle of the link is steep. As it compresses it pushes that side of the axle back. Extension pulls it forward. Add in the narrow chassis and it is even more pronounced.
So what is happening? Lets take a sweeping right turn (same happens in left but once you figure the right you can reverse for the other direction). You go into the turn and steer a little to the right. Vehicle reacts, you get a little body roll. The outside rear tire (left side) arcs back a tiny amount and the inside tire (right side) arcs forward a little. This steers the rear axle a little and makes the Bronco turn right. But you already are steering to the right with the front axle. You are getting more right hand yaw then desired. So you straighten out the turn. This unloads the body roll, the rear axle straightens out, now you just lost both the front and rear steer. But the road is still turning right. So you steer back into it. Everything repeats. You find yourself sawing the steering while in a turn. Often thoughts are the steering is too fast and you can't get the angle you really want. That is partially true, the desired angle is more difficult to reach. A slower steering box will more gradually load and unload the chassis (and body roll) in the turn and give you a better chance at finding a happy spot in the middle. If you could eliminate the roll steer (or even better reverse the direction of the roll steer) it will make sweeping highway curves feel like you are taking them in a much longer wheelbase vehicle.
This is one area where a flatter spring and blocks actually help. Yes, evil lift blocks can be good as strange as it sounds. If you look at most trucks you will see the front spring mount is fairly low, often below the bottom of the frame. It is often a straight shot to the axle housing, sometimes even with a slight rise to the axle mounting point. The arc then goes up and the shackle mount is almost touching the bed. This is for roll steer. You get an F350 and it has factory lift blocks. Not because they were cheap and used the same springs (which they have been known to do), but to get the extra height and keep the correct spring geometery for the roll steer. They didn't have to change the spring perch locations.

Oh the joys of suspension. There are 2 or 3 good chassis books I could refer you to if you really wanted to get deeper into this (and I only scratched the surface here). http://www.addco.net/aftermarket/tech/handling-book/ is a nice little starting point. I got a printed copy at SEMA a few years ago and have found it a great simple reference. Looks like the online version is still the same 2005 that I have. I will have to find the books at work for the fancy formulas. I have not seen them in a while, I hope they have not walked away. They were expensive books.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Tim, would the drop brackets increase the drive shaft angle?

Yes they would. So if you're running the 6.25 bushings and your u-joint is already close to binding, they could be enough to put it over the limit.
Add another 4 degrees with the drop brackets and your caster would be +6, but the trade-off might not be worth it.
Every rig is different, so you'd have to verify that in your particular case. But there's a strong chance of it.
If in doubt, I would go with the previous recommendation of using the lower C-bushing value and doing it all at the outer steering axis. You can keep your existing bushings of course, and just rotated the yokes back at the top 4 or 5 degrees and be done with it, but your pinion would still be at it's current angle. So you need to put that into the equation as you figure out which way to proceed.


I can get the work done for about 150-200. in chattanooga. im wanting to be able to drive it to townsend in a few months.

If you mean for rotating the steering yokes, for $200 or less, I'd say that's not a bad deal. You can do it yourself of course, but if time is money, that 200 starts to look well worth it.
And yes, the "outer C" is actually called the "steering yoke" and as you guys were saying, it's the part where either the ball-joints (later 44's) or king-pins (earlier 30's) are located. Not where the C-bushings go.

The yokes proscribe the "steering axis" and dictate at least two common alignment properties (three if you include camber).
The two basic ones though, are Caster and Steering Axis Inclination (the "SAI" you see on some charts). Camber is effected by the steering axis inclination, but is actually measured separately from SAI. Relative to the spindle instead I would imagine?

So then Positive Caster, as you know, is the rearward tilt of the top vs the bottom of the yoke.
SAI is the inward (on Broncos at least) tilt of the upper vs the lower pivot points of the yoke.
Camber is inward or outward tilt too, but of the tire only, which takes into account the designs of the spindle and knuckle AND yoke as an assembly. I'm guessing they consider the spindle the center of that universe though.

Just thought I'd add to your confusion.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hmm, I guess I didn't see bowsher's input before posting. He's got it all down there so I'm just duplicating some of it.
It's what happens when you read, start writing, then go deal with the usual family emergencies before finishing things up.
I try to remember to refresh first, but get on a roll. You've seen how I can be...

Paul
 
Top