• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Stubborn screws

Mac2Night

Bronco Guru
Joined
Aug 10, 2005
Messages
2,204
So I need to adjust a striker but the backing nut plate is toasted with rust (tried spraying it) and I can't turn the screws to break them loose. What in my next option? Is there anything I can do other than drilling them out?
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
A short phillips head bit and a 1/4" drive ratchet will help - don't know if it will do it for sure but you'll get a whole lot more torque using a 1/4" ratchet than with a regular screwdriver

Lubrication, heat, and-and all potentially needed but I'd start with the least messy and destructive

Good luck

DJs74
 

broncobilly72

Full Member
Joined
Nov 8, 2010
Messages
349
impact is the way to go....just read the directions.The impact of the hammer tends to loosen all the rust.
 

wepuckett

Sr. Member
Joined
Apr 28, 2014
Messages
721
All an impact is is a hammer beating against a ratchet so if you don't have a HF close by or don't wanna spend money pull out the ratchet and put the screwdriver bit needed on it with the attachment and take your hammer and tap repeatedly the end of the ratchet or put a bar over the ratchet and give yourself more leverage and bust it loose. Impact is always a very nice option but if you don't have the tool already who wants to go drive 20 miles or more or over pay for the tool.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Had a similar issue doing brakes on a buddies man rover. Why the euros use a phillips head on a drivetrain part I dont know. Another friend pulled an impact screwdriver out of his toolbox. It worked like acharm. I ordered a 1/2 and a 3/8 kit from lisle for my garage
 

mlogan24

Bronco Guru
Joined
Jun 14, 2001
Messages
1,380
All an impact is is a hammer beating against a ratchet so if you don't have a HF close by or don't wanna spend money pull out the ratchet and put the screwdriver bit needed on it with the attachment and take your hammer and tap repeatedly the end of the ratchet or put a bar over the ratchet and give yourself more leverage and bust it loose. Impact is always a very nice option but if you don't have the tool already who wants to go drive 20 miles or more or over pay for the tool.

Sort of . . . it creates rotational torque. What you just described is a good way to ruin a ratchet.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
+1 (I can't count that high ;D)

An impact is a VERY useful tool to have, especially when working on old vehicles. But don't skip the penetrating oil - keep the backside of the plate wet for a few days.
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
that is what I used to get mine out, but I bought mine at Napa. I think it was like $12.

X whatever. We use them in the Air Force. Usually after a Crew chief dix up a screw that's what we grab first after being dispatched to an aircraft. Machinists are the only guys that are allowed to use it. But if that doesn't work we go to the tried and true screw remover: easy outs. No matter what size the screw or bolt, we have an easy out for it. For AGE stuff we might have to drill all the way thru without hitting the parent material. We don't use any sort of penetrating oil, just heat. Sometimes heating a hollow-out bolt only will loosen it up. When all else fails we go digging for the pencil grinder. Nothing worse than being in the intake of an aircraft pencil grinding away a stainless steel bolt way down in Key West FL in the middle of August. You wanna talk about hot, especially after getting a damn QA write-up bc I didn't wear the freagin booties! G'ahhhh!
 
Top