• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

vacuum gauge & timing

OP
OP
blubuckaroo

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I guess what I'm asking is, if I adjust the timing at idle with a vacuum gauge now it runs great at 600 RPM. Is it still set properly to run at 2000, or 3000 RPM or will it ping like crazy?
 

oleguy74

Contributor
Bronco Guru
Joined
Mar 26, 2008
Messages
2,034
Loc.
calif city ca
yes.you are doing the same thing as with a timming lite only using vac gauge.use a timming lite while you do it so you will know what timming is,as long as your advance works you will be ok.
 
Last edited:
OP
OP
blubuckaroo

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
yes.you are doing the same thing as with a timming lite only using vac gauge.use a timming lite while you do it so you will know what timming is,as long as your advance works you will be ok.

I'm using both. Please explain how initial timing with both a vacuum gauge and timing light at 600 RPM can be of any value at 3000 RPM. Sounds like by-guess or by-golly to me.
 

oleguy74

Contributor
Bronco Guru
Joined
Mar 26, 2008
Messages
2,034
Loc.
calif city ca
think about it!!!you don't set timming at 3000 rpm do you?no you set it at idle.using the timming lite will give you a refference when vac is at best.you may still have to adjust a little one way or another.example...vac peaked at 18in.timming lite says youre at 15*btdc.run it and fine tune i with lite .500-800 rpm is a good idle speed.your mechanical and vac advance takes care of off idle to what ever you run it at...
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
set it up at idle.
Then check timing as you advance up, graph it in a spread sheet record readings at 1K 1.5K 2K 2.5 K ect....
at some point in the graph it will max out this is your timing curve, this can be adjusted 2 ways mechanical and vacuum, most of the vacuum modules are adjustable , stick an Allen wrench in the port and tighten or loosen the diaphragm, or change the spring & weights in the distributor.

Take if for a ride and find a hill and see if it pings, if it does you have too much total timing ( initial +vacuum+Mechanical= total timing) good target is 32-34 degrees
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yep, what they said. Adjust at idle, but check the rest, just to be sure it's what you want. The individual advance curve built in (or added) to the distributor's advance mechanism(s) is what takes care of the rest.
What you're doing at idle, is getting the ballpark with the vacuum reading, then tweaking things if needed. If what you did at idle doesn't give you optimum results at other rpm levels and load values, you adjust for best "compromise" readings.

The only way to get the best of all worlds is to modify your advance curve to suit your individual vehicle's needs. That's only done by changing springs, weights, and vacuum range adjustments (the screw that ransil was talking about).
Anything else is just compromise OR luck.

So your thinking is on the right track, but you can't change the actual relationship of one to the other by twisting the distributor. Unfortunately, it's not that simple. Otherwise you'd need to do it at all rpm ranges while driving.
They tried that with things like an MSD Adjustable Timing Control box. Nice, but not optimum either.

All the hot-rod shops back in the day used to have a dizzy machine that they could re-curve your distributor for you to meet your needs. It was never cheap (someone else's time never is), and most speed shops are long gone now and it's all about mail-order and the internet to get the lowest price.

Best thing currently, to make it right at all times, would be the new Mallory electronic distributors that have a digital advance mechanism and a MAP sensor built in. You flip the switch to one of five different advance curves till you find the one you like, OR, you program your own with your PC to suit your needs.
Very 2000. Unlike stock, which is still very '50's!!!!

Paul
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I'm using both. Please explain how initial timing with both a vacuum gauge and timing light at 600 RPM can be of any value at 3000 RPM. Sounds like by-guess or by-golly to me.

I personnally dont feel a vacuum gauge is all that benifical to setting the timing. As vacuum greatly varies once a load is introduced which doesnt help when tuning in your driveway. Timing light on the other hand will tell you exactly how much timing you have at both 600 and 3000 RPM and anywhere in between.
Basically because the dizzy uses a mechanical advance that depends on RPM's and counterweights to change the timing over what it was at idle. A typical SBF needs a total of around 34 degrees timing which is best to have all in by 3000 RPM.
Now say you have 10 degrees timing at idle(kinda set in stone even though you can adjust it but still once set that number is what you have) Well you still need about 24 more degrees to run down the road and make any power. Most of that if not all should come from the mechanical advance. Lastly comes in the vacuum advance which kinda is a stop gap meaning that as the RPM's increase and vacuum remains high then the vacuum advance will advance/retard the timing as dicated by engine load. The vacuum advance will also fill in where the mechanical advance has not yet caught up yet So at 1200 rpm where the mechanical advance has just started to increase and vacuum is high the vacuum advance will give you that extra advance (probably around 20 degrees). So you have a intial timing of 10 then mechanical of say 4 and vacuum of 20 all adds up to about 34.
This is not all set in stone as engines can have more than 34 degrees of timing and still run good and not ping at lower RPM's but once your around 3000 rpm that 34 degrees becomes important
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Both ways work, best is to use a little of each: vacuum and timing to get what you need. it's an art, not science like an ECU program.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
The vacuum gauge is a glorified "tuned by ear" when you replace your ear with a gauge. Close and often close is good enough. I have had engines that really could care less what the timing is set to. Then other engines that a little bump in timing completely changes the engine.

timing light will get it right. Vacuum gauge is an aid to those who can't tune by ear. I am one who can't tune by ear. But I finally got a timing light years ago and am a lot more consistant in my set ups now. 14° and ping, 11° and it's a dog. I can dial in that 12-13° with a light that the vacuum gauge just can't tell the difference.
 
Top