What have you done to your Bronco today?

[73stallion]

Drove it to Monarch Bay car show. First time out of the driveway in about 3 weeks.

 

[pat1977]

Got my cage welded and seats installed.and also the cage part for my seats.

Sent from my SPH-D710 using Tapatalk 2

 

[Z Bronco]

Ordered more parts.........and motivation......

 

[RV77]

Re-wired my flashers. Combined the Emergency flasher and the Signal flasher into a single LED (no load) flasher unit.

View attachment 272057

Where did you get the flasher ? Thanks

 

[xcntrk]

Where did you get the flasher ? Thanks

http://www.superbrightleds.com/more...rs/ep27l-led-bulb-electronic-flasher/784/838/

 

[Rox Crusher]

installed my new door panels

 

[hdfx81]

Put on new spark plug wire looms.

 

[miikee73]

Just ordered a 1 inch body lift,and a few other things in preparation for my NV3550/AX15 (not decided yet). The body lift will address other issues even if the trans mod doesn't happen .$$$$$

 

[twisted77]

Just ordered a 1 inch body lift,and a few other things in preparation for my NV3550/AX15 (not decided yet). The body lift will address other issues even if the trans mod doesn't happen .$$$$$

Are they not the same trans?

Bryce


Sent from my EB parts finder phone.

 

[twisted77]

Had to go junk yard tire shopping for my daily driver, sorry it's a gmc. Anyway got a deal on a nearly new set of tired and nice wheels. Tires new are almost 1000 I got both for 650.

Anyway bronco related I found an 5 speed on a Toyota am I wrong or is this an Ax15? I'm not up on toyotas.

Bryce


Sent from my EB parts finder phone.

 

[miikee73]

Are they not the same trans?

Bryce


Sent from my EB parts finder phone.

They are not the same trans,different manufactures. I'm no authorty on this subject.They are very simular,may even use the same adaptors.

 

[BALCH-Autoworx]

I pulled the passenger side head . . . about a month a ago I pulled the valve cover after it sat for a 6 months to find a broken exhaust valve on the number 2 cylinder. Good news, no obvious piston/block damage, bad news I had really bad oil pressure even with a brand new pump. I could get it running cheap with a new valve, spring, pushrod . . . but I spent the afternoon shopping for crate motors.

A new motor isn't exactly in the budget, shipping to Hawaii will suck, but I have to keep the Bronco running, its been too long already and I could be moving back to the mainland as soon as July. Shipping gets really expensive when the vehicle doesn't run . . . so really I am saving money right?

Anyone have experience with ATK or BluePrint 408Ws?

 

[Dan74Bronc]

Bent and hooked up trans lines to my new C4 trans. Ongoing project.

 

[sriha]

Backed it out of the garage, moved some stuff around and put it back in

 

[phred]

replaced the coil and coil wire, hope that solves the intermitent ignition issues. Already replaced the duraspark module.

 

[xltbeast]

Took out the C4/ Dana 20 and removed the c4 tailshaft to go into a new tranny. Spent to much time in the garage so now my 302 is missing heads and an intake. Time to place an order for some new parts....

 

[blamejane]

Finally reinstalled the liftgate access panels. Also tried to attach the front license plate frame to the front bumper. I’ll have to purchase smaller carriage bolts to get this completed. Daily driver for the day!

 

[ahansen_1985]

Built most my exhaust, and started on the inner fenders
Now I can hear the tires howl ...


1966,351w,m5od,205....3.5" lift, 2" body, 38.5's

 

[sprdv1]

All unloaded and back in the garage spot... ready for some soap and water this weekend...

 

[okie4570]

Moved the rear seat back further.