• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Timing?

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
What should i be looking for when setting the timing? how much advance should there be? it cranks and runs im just wanting to double check everything. its 302 very mild cam. with hei. Correct me if im wrong but to set the advance its done with the vac line off and pluged?
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
Yes, that is correct. Usually you want to start out with 8* before top dead center and you can tweak it from there.

On my all stock rig, and a friends rig I found that it works best to have 12* of advance and NO vac advance. Over two days of solid testing and it came up to me that was the best for throttle response and low end power.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I wish it could be that simple.
Vacuum advance is the load control for timing. With a load, vacuum reduces and so should the timing advance.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Reverse that. Under load and low vacuum, the timing is retarded back near, or to, whatever the static plus mechanical timing is.
Under coast or low-load situations, when it can handle more timing for better efficiency, the higher vacuum signal advances the timing.

Vacuum advance is almost always a good thing for a street/trail engine. Unless it's not working properly.
Even racers would occasionally benefit from it, but the main reason they don't use it is that getting rid of it means one less thing to fiddle with or go wrong during a race. Some don't even use mechanical advance and instead just set static timing at their chosen spec.
Those that still use it can get pretty much anything they need out of mechanical only advance. For us vacuum advance is mostly a benefit.

And if your carb is working as expected, there should be next to zero vacuum signal at the hose during idle anyway. So if all is as expected, you should not even have to unplug the hose while you're setting the base timing.
Yes, it's still the recommendation, to overcome any potential variables, but if you put a vacuum gauge on your hose and find that there is no signal at idle, there's no benefit in removing it for initial setting.

Paul
 

Kimmel 44

New Member
Joined
May 10, 2010
Messages
37
Loc.
St. Louis
I have a stock 76 and wanted to get more pep out of the stock motor. I remember being told that the stock motor in 76 was retard some for econ reasons. Should I get it timed back up to 12 deg advanced for the most throttle response for in town driving?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I would at least give it a try. In the late seventies they were trying all sorts of things to get the emissions lower. Retarded timing (in some cases all the way to AFTER top dead center even!) was just one of them.
I would certainly experiment. It's easy enough to do. Give it a few degrees here and there until you find the sweet spot where it runs the best but does not ping under hard acceleration.

I ran my '71 at 14° most of the time. Anything approaching 10° should be an improvement.
Just be aware though, "your results may vary" as we have learned to say here.

Paul
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Paul or Anyone,

Don't mean to highjack but this is vacuum adv related.
I remember years ago being told that hooking your vacuum advance up to steady vacuum off the intake instead off of the carb would help with "idle advance cooling". Does anyone ever remember this and would it help our eb's run cooler atleast at idle? If not any benefit at all.
Thanks.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Can't really say it will or it won't, since I've never been able to get any motor I've had to run well with full manifold vacuum. I know some engines were set up that way from the factory, and some people have said that theirs run better that way, but that has not been my experience.
So I never ran it that way long enough to find out whether it helped with cooling or not. And since I never really have had any cooling issues with my Bronco, it's never been something to pursue.

You can try it, but if my experiences have anything to say about it, you won't have much luck. Your timing will be high at idle, but then immediately come down as you accelerate. And you have to set your static timing so low to compensate, that when the vacuum is reduced, your timing can end up so retarded that it just won't have the pep you're looking for.

But here again, every setup is different it seems, so whatever your issue might be, experimenting can be fun a profitable. Up to you then. Who knows. It might be just what the doctor ordered.
But I say no, it won't run right.

Paul
 

red hot71

Sr. Member
Joined
Nov 26, 2009
Messages
654
Loc.
kent wash.
Ok here's another one. I been reading if you run a GM type or HEI on a Ford that you should run full vacuum advance because that's the way GM designed it, but if it's a Ford type design that timed (ported) vacuum is the way to go. I guesting that it's all in the design of the vacuum advance canister?

I think to take advantage of all the timing options (mechanical and vacuum) you need to run premium fuel with 8to1 compression. Back in the day 1969 or so regular fuel was 91-92 & premium at 100-102 and low compression was 9to1 plus, and it was real gas.
 

redtail

Sr. Member
Joined
Jul 14, 2010
Messages
621
I have a stock 76 and wanted to get more pep out of the stock motor. I remember being told that the stock motor in 76 was retard some for econ reasons. Should I get it timed back up to 12 deg advanced for the most throttle response for in town driving?


Just as important as the ign timing is the cam timing. The cam timing was also retarded at that time. I advanced the cam and advanced the timing and now it runs like a dream.

As far as vac advance, I have found that each engine combination runs differently and so each requires a different setup.

for me it makes sense to only have mechanical, as rpm is a good indicator of what timing events you need. Low rpm heavy or low load needs less timing than high rpm heavy or low load. My timing is set up so that it does not ping under hard use. All around it made my set up much peppier. It seems less 'confused' when I go to stomp on it.
 

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Great and timely%) information. The vacuum advance on my stock 76 is hooked up to direct manifold vacuum. This may be some of my ruff idle issues. Where does the vacuum advance hook up to, on the 2150 carb? Looks like I'll be playing with the timing this weekend.:cool:
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Great and timely%) information. The vacuum advance on my stock 76 is hooked up to direct manifold vacuum. This may be some of my ruff idle issues. Where does the vacuum advance hook up to, on the 2150 carb? Looks like I'll be playing with the timing this weekend.:cool:

There is a port on your carb that will have little or no vacuum at idle but full vacuum upon acceleration. It should be easy to find. On a Holley it is on the passenger side of the front metering block.
 

nathan.hall1

Sr. Member
Joined
Feb 3, 2006
Messages
556
Loc.
Central Washington
Ok here's another one. I been reading if you run a GM type or HEI on a Ford that you should run full vacuum advance because that's the way GM designed it, but if it's a Ford type design that timed (ported) vacuum is the way to go. I guesting that it's all in the design of the vacuum advance canister?

you can do that?

I just googled it I found my new distributer.
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Don't forget to read all about it here too Nathan. Just to get the good and bad from those that have used one.
Or did your Google search point you here in the first place?

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Ok here's another one. I been reading if you run a GM type or HEI on a Ford that you should run full vacuum advance because that's the way GM designed it, but if it's a Ford type design that timed (ported) vacuum is the way to go. I guesting that it's all in the design of the vacuum advance canister?

I'd say it still depends on the whole setup. How is the timing curve designed in the distributor? Even though it's based off of of the GM/HEI design, is the curve generic, or is each one tweaked for the intended application?
And not all GM vacuum advance specifications called for manifold vacuum if I'm not mistaken. Because of that, and the fact that you're still running it on a Ford, and that your Ford is not even stock any more (most likely anyway), you probably still have experiment for your best performance.
Try it both way to see what makes you happy. Your results may vary...


I think to take advantage of all the timing options (mechanical and vacuum) you need to run premium fuel with 8to1 compression. Back in the day 1969 or so regular fuel was 91-92 & premium at 100-102 and low compression was 9to1 plus, and it was real gas.

You're right about the octane and (mostly) compression ratios, but your basic Broncos did not come with the higher compression setups even for their time. And with wedge-shaped combustion chambers, most years EB's were pretty forgiving of detonation/pre-ignition/pinging.
If I remember the peak for a Bronco V8 was in '66 and '67, would have only been about 9.3 to 1 ratios. It was all down hill after that. Mine probably has about 8.5 to 1, while the mid to later seventies EB's were nearer 8.0 to 1.
Fairly forgiving, even on today's gas (here in CA anyway, not sure about elsewhere) and any engine can benefit from fine-tuning the advance curve to best take advantage of all of the fuel during combustion under different circumstances.

So tweak away. Experiment with timing (static, mechanical and vacuum) until you're blue in the face. Listen to what works and what doesn't with those that have modified their curves.
Even a low compression engine on today's regular grade fuels can utilize vacuum advance to good effect. The OE's ran vacuum advance distributors on engines all the way into the nineties.

Lots of members here using the DUI and it's clones to good effect. My personal favorites though are the new Mallory electronic distributors Max-Fire and E-Fire (like this http://mallory-ignition.com/max-fire-distributor-ford-w-comp-9000.html) with electronic advance.
You set the curve with a dial, or custom tune your own with the included software on your home computer or laptop. Self contained and multiple sparks in one of them too. The vacuum advance is a modern MAP sensor instead of a mechanical dashpot. Very cool stuff.

I'm really interested in this distributorless setup too now though. http://www.compu-tronix.com/DIS8.htm
Great idea that.

Have fun deciding and experimenting!

Paul
 
Top