• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Major EFI problems

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
Alright guys, I've put up a few of these posts but they all ended up being confusing.

What I have:
Ford racing 306
24lb injectors with calibrated maf
Explorer intake

Rjm harness
Bcbronco fuel kit

All new sensors except the map? I think that's what it's called, the one that does the pressure.

New sensor on distributor
New coil

From the last time I ran codes it just came up with smog stuff, I don't have any of it so its fine.

Tps is set right, idle is set right.

The problem is, it will start fine, it will run but feels like it has a miss almost, just doesn't run smooth, then when it gets hot it will die, then it won't start again till it cools down. I've literally done everything I can think of to this thing, I stated the swap almost a year ago now, this school year I'm at college so I can't work on it as much but it's just been a pain!

I'm trying to find someone in the Bay Area that is good with this swap that can possibly come by and help me out.

Any other suggestions welcome too!

Thanks Evan
 

TBS-POPS

Bronco Guru
Joined
Jun 16, 2007
Messages
1,388
Loc.
valley springs, ca
It's starting and running on the cold run enrichment circuit (efi choke as it may be). when it gets to temp it's supposed to lean down and run on the regular run circuit. yours is not for some reason. Check for vacuum leaks also. when the system goes into lean run it could be too lean to run. maybe why it runs weird when cold and in rich mode.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Is this a new setup or has it been running?

What MAF are you running with those 24# injectors?

Fuel scheduling aside, I have seen folks have TFI issues related to temperature.
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
It's starting and running on the cold run enrichment circuit (efi choke as it may be). when it gets to temp it's supposed to lean down and run on the regular run circuit. yours is not for some reason. Check for vacuum leaks also. when the system goes into lean run it could be too lean to run. maybe why it runs weird when cold and in rich mode.

That seems like it could be part of it, what should I do to try to fix it? I'll check again for vacuum leaks but I'm pretty sure there aren't any
 

tatersalad

Bronco Guru
Joined
Jan 17, 2009
Messages
1,067
Is it a new coil? It sounds like the coil could be heating up and then shutting down, once it cools back down it works again.. I had one do that once on the way to Truckee, it would get hot and then die, i poured bottled water over it to cool it down and then it would restart and I would take back off and get about 5 or 6 more miles until it reheated and quit again. When I made it to Truckee, I purchased a new one and all was good : )
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
Is this a new setup or has it been running?

What MAF are you running with those 24# injectors?

Fuel scheduling aside, I have seen folks have TFI issues related to temperature.

I'm not positive, I just got it off Craigslist a couple days ago, the guys said it was a ford one that was re calibrated. I got the motor last year and had a carb on it ran great except off road, put tbi efi and that wasn't working too great so I did the ford efi and it worked but ran rough and it just gets worse and worse, use to just stall every few hundred miles, now it does it after a few miles down the road.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I'm not positive, I just got it off Craigslist a couple days ago, the guys said it was a ford one that was re calibrated. I got the motor last year and had a carb on it ran great except off road, put tbi efi and that wasn't working too great so I did the ford efi and it worked but ran rough and it just gets worse and worse, use to just stall every few hundred miles, now it does it after a few miles down the road.

This MAF is likely to be your problem. Will it run better with the MAF unplugged?
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
No this is my 3rd maf, does the same with all of them, and second computer, maybe I need to get it tuned?
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
The MAF must be calibrated to work with the injectors. I frankly wonder why your using 24# injectors on a relatively 'standard' 302? I'm going to guess that it's running rich? For a 'mild' 302 all you need are 19# injectors and a stock explorer or mustang GT MAF, nothing fancy needed, but they must match or you'll have all sorts of issues.
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
Well I had 19s and it was lean, and the manual from ford says this motor needs 24-30 lb injectors. It has a cam, aluminum heads, and suppose to make 340 at the crank
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I had the same problem once. Turned out I had the wires to the O2 sensors backwards

Good point - I think it may be O2 related by the way it runs ok on a cold circuit but when it starts reading the O2's (after the warm up) it gets a funky signal and runs poorly. If it does that, unplug the O2's and see how it runs-

It should go into open loop and run -
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Did you install it with thermal paste? (Like the kind that goes between a computer CPU and cooling fan)

Thank you for not saying "thermal grease" - the idiot "professionals" at work have not problem calling it that.... %)
 

lonicus

Full Member
Joined
Dec 27, 2009
Messages
267
Loc.
Costa Mesa
Alright guys, I've put up a few of these posts but they all ended up being confusing.

The problem is, it will start fine, it will run but feels like it has a miss almost, just doesn't run smooth, then when it gets hot it will die, then it won't start again till it cools down. I've literally done everything I can think of to this thing, I stated the swap almost a year ago now, this school year I'm at college so I can't work on it as much but it's just been a pain!

That part makes me think to look at your dizzy. Have you replaced that? When I did my swap I used a junkyard dizzy, worked like crap until I replaced with new unit.

Just had to replace my TFI to (hopefully) fix my random shutdown issue. (Engine will turn off unpredictably, then requires the TFI to be unplugged and re-plugged in to start)

Anyway, while trying to figure out what it was, I saw a lot of posts about heat and the hall sensor getting all screwed up. Not my particular problem, but might be yours?
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
My dad just called me and said that when it died on him today he checked for spark and wasn't getting anything, so I think it has to do with something with the dizzy, it's junkyard with a new TFI, I'll replace the whole dizzy and see what it does. The o2 might also be a problem but it doesn't run well at anytime really
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Yep. It runs for the first few minutes without the o2 sensors in the loop until they are warmed up enough to provide adequate data.

If you unplug them, it will just stay in open loop mode and run off the table data.
 
Top