• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Major EFI problems

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
Yep. It runs for the first few minutes without the o2 sensors in the loop until they are warmed up enough to provide adequate data.

If you unplug them, it will just stay in open loop mode and run off the table data.

Good info- wasn't sure how I was gonna get mine to the exhaust shop.
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Are you running a BAP (mass air) or Map (speed density?) If you're running Mass air, make sure your BAP is NOT connected to a vacuum port.
 

Ranchtruck

Sr. Member
Joined
Feb 7, 2008
Messages
768
All new sensors except the map? I think that's what it's called, the one that does the pressure.

He's asking to make sure you don't have a vacuum line attaching this sensor to the engine. If you do, the computer will think the truck is on top of Everest and lean the mix way out. It's used as an atmospheric pressure sensor on the MAF trucks and should not be connected to the intake manifold vacuum.
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
He's asking to make sure you don't have a vacuum line attaching this sensor to the engine. If you do, the computer will think the truck is on top of Everest and lean the mix way out. It's used as an atmospheric pressure sensor on the MAF trucks and should not be connected to the intake manifold vacuum.

yeah it doesnt, there is just a little plastic cap on it




ill unplug the o2 and see how it does, and if it still happens ill change the dizzy out, get new plugs, use different wires, and see if that helps

And does anyone know how to use a break out box? i think thats what its called, another member let me use it to text my first harness but i never got around to try it out, would that fill me in on any other info that could help?
 

bronco italiano

Bronco Guru
Joined
Feb 1, 2004
Messages
2,595
I work in redwood city, if your near I can come by and take a look.

-I had similar issues with my bronco.

BI
 

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
From what I recall, there is an issue like this if running a manual computer (a9l or similar) with an auto harness, or vice versa. The ground pins are in different positions and you can fry the computer, causing it to do something like what you describe.

Look for a longer post started by ransil on the topic.
 

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Good point Bart. Just open the EEC and look for burned trace. It is easy to fix.

Sent from my Droid using Tapatalk 2
 

BUCKNBRONK

Sr. Member
Joined
Jun 30, 2011
Messages
521
Loc.
fresno
i know when I got my harness from centec i had a super rich condition for the longest time, sent the harness back 3 times,it ran ok but i was getting like 5 mpg, tried all new sensors, no help. finally my auto tech friend told me to check the +- orientation on the map sensor - it was back wards from centec all that time. fixed it and was good to go. they put out a lot of harnesses check ur sensor plugs for the correct orientation of the pins.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
My dad just called me and said that when it died on him today he checked for spark and wasn't getting anything, so I think it has to do with something with the dizzy, it's junkyard with a new TFI,
When it dies and has no spark, try disconnecting the SPOUT connector and see if it gets spark.

When the SPOUT (SPark OUT) connector is in place, the pulse from the distributor pickup is routed by the TFI to the EEC through the SPOUT wire. The EEC then determines the correct timing for the conditions and sends back the spark pulse to the TFI, which in turn grounds the coil and makes a spark.

But if the TFI sees no spark signal coming back from the EEC, it will fire the coil based on the pulses from the distributor. This is how the base timing is set.

So, if there is a wiring harness or EEC issue, you should get spark with the SPOUT pulled. If no spark with the spout pulled, then it could be several problems, including no power to the TFI. But, it should be local to the distributor/TFI.
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
Not that this is your problem, but you should try this. A friend of mine had a nicely built 351 that he thought he needed 24lb injectors and it ran like crap with 24 lb injectors and some aftermarket MAF. He put some Explorer 19lb injectors on and a Explorer MAF and said he felt like he gained 50 hp.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Not that this is your problem, but you should try this. A friend of mine had a nicely built 351 that he thought he needed 24lb injectors and it ran like crap with 24 lb injectors and some aftermarket MAF. He put some Explorer 19lb injectors on and a Explorer MAF and said he felt like he gained 50 hp.

The explorer MAF is not a good match for the mustang ECM. It may be better but it still isn't right.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Snag a maf from a 5.0 towncar or 3.6 cougar that has the A1A or A2A on the tail end of the part number. They are 70mm mafs and work fine with mustang eecs. There is also an oem maf for 24lb injectors but i cant remember the details at the moment.

Sent from my Droid using Tapatalk 2
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Snag a maf from a 5.0 towncar or 3.6 cougar that has the A1A or A2A on the tail end of the part number. They are 70mm mafs and work fine with mustang eecs. There is also an oem maf for 24lb injectors but i cant remember the details at the moment.

F2VF-12B579 is the 70mm MAF that works with 19 lb injectors and mustang ECM (A9*).

OEM 24 lb injector MAF and injectors are only good with the cobra ECM.
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
Alright lot of info there, I don't think it's the injectors or maf because I just put those in a few days ago and it didn't make a difference, I had 19s in before.

And the wires to the maf, do I just check to see if the wire colors are matching?

I have a auto computer and auto now, I'll make sure I set the connector in the harness to the right one.

Thanks for all the info guys
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I think what he was saying is that if you have been running the plugs in the wrong position it may have fried the trace. Now I know it is only one of the two combos that does this but I cant remember which it is.

Anyway, the MAF connector for 89-95 is typically as follows:

RED- LTGR/BK- LTBL/TAN- ORG/DKBL
 
OP
OP
77broncodriver

77broncodriver

Full Member
Joined
Nov 21, 2009
Messages
344
so if its plugged in the wrong way then i could have fried the computer and maf or just computer?

or am i still missing what you guys are saying?
 
Top