• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Engine angle

laen61

New Member
Joined
Aug 9, 2013
Messages
1
I am installing a new 351 with a 4R70W and a NP205. Since I need to build a new transmission mount I was wondering want the angle of the engine should be. I thought it was 3 degrees down, but not sure.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
with that powertrain set up I would be more interested in front / rear drive shaft angle

Its a give and take. if you go higher in the back the angle on the front shaft gets better because of the 205 front output is pointing upward. However going up will make your rear angle worse. Unless you clearance your front CV you will have bind issues at full droop . Play with it. find a happy spot.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
If it is carbed then make the carb mounting surface on the intake LEVEL. If fuel injected set a carb intake on It to install and then switch out
 

Rymadd

Sr. Member
Joined
Jan 24, 2013
Messages
470
I could be wrong, but I always thought your engine was supposed to be tipped back just a few degrees. Not sure why but I have heard that multiple times...

Not sure if it is for carburation or oil returning.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
The original trans mounts or adapter mounts are at an slight angle from the factory on the frame holes. . I don't know if it s right but I just kept that angle when I had to build my mount for the 4r70w. Kept the angle and extended the back.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I don't have the numbers for an eB, but this chart shows them for a FSB:



The TSB linked in that caption also shows how to set the d'shafts correctly on any modified vehicle.

The engine angle isn't critical - you can't set the front height - you're limited by the engine mounts & the frame perches. Just set the trans Xmbr as high as possible so you still have body clearance over the t-case.
if you go higher in the back the angle on the front shaft gets better because of the 205 front output is pointing upward. However going up will make your rear angle worse.
That's a common mythconception - lowering the t-case makes BOTH d'shafts' angles better because the flex angle decreases much faster than the tilt angle increases.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
Yes the engine should be tipped back a bit. If you look at the carb mounting base it is angled so the front is closer to the intake than the back. So if you mount the engine so the carb base is level you should automatically get the engine tilt u need. Look at all carbed engines. The air cleaner and top of carb are always level. But if you look at the valve covers they slant back towards the firewall
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
I don't have the numbers for an eB, but this chart shows them for a FSB:



The TSB linked in that caption also shows how to set the d'shafts correctly on any modified vehicle.

The engine angle isn't critical - you can't set the front height - you're limited by the engine mounts & the frame perches. Just set the trans Xmbr as high as possible so you still have body clearance over the t-case.That's a common mythconception - lowering the t-case makes BOTH d'shafts' angles better because the flex angle decreases much faster than the tilt angle increases.

Steve, I'm just going to disagree with you.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Steve, I'm just going to disagree with you.

Who are you going to believe..him or your own lying eyes?;D

Had the same experience as yours, twice myself; determining what angle to mount the flathead V-8 drivetrain in the '69 (5" SL) and the 408-C/NP435/NP205 in the other '69, also with 5" SL.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Yes the engine should be tipped back a bit. If you look at the carb mounting base it is angled so the front is closer to the intake than the back. So if you mount the engine so the carb base is level you should automatically get the engine tilt u need. Look at all carbed engines. The air cleaner and top of carb are always level. But if you look at the valve covers they slant back towards the firewall

Engines are very often mounted angle up but not for any reason related to the engine itself; its to get the best overall fit. The engine had to be above the front axle but the tranny couldn't be too far up in to the drivers compartment.

Early sports cars, on the other hand, kept everything nice and level by simply putting a huge tranny and driveshaft hump right through the cockpit.

The 351C in my '72 Pantera is perfectly level.;D Pretty sure the 289s and 427s in AC Cobras were level too.


If you noticed, modern vehicles seldom have angled engines any more either; they've typically figured out better ways to fit them in to the vehicle.

Conversely, marine power plants for smaller craft are mounted at angles that can reach 15 degrees. Many earlier manufacturers that used automotive engines for their base powerplant actually mounted the marine transmissions on the "front" of the engines so that it was the front of the engine angled so far down. That way, the timing gears and/or chain were well oiled while the flywheel and starter were more elevated from the bilge and potential water splashing.
 
Last edited:

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Too low and the back of the heads will mash the firewall
Too high and you will be into the floorboard and the fan will be in the bottom of the shroud.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Too low and the back of the heads will mash the firewall
.

Yup. Like my 408C does; I had to modify the dr side of the firewall to clear. Bax tilted his tranny up just a little more and didn't have the same issue.
 

Fairlane514

Sr. Member
Joined
Oct 28, 2013
Messages
508
Loc.
Houston
I mounted a 460 in my 63 Fairlane with 4 degree tilt back for oil flow return.

I placed an angle finder on the intake manifold (with carb off) and gave it 4 degrees. Its not much, and yes it a two wheel drive vehicle, so there may be a point to the front and rear drive shaft angle.
 

broncojo

Full Member
Joined
Jun 25, 2013
Messages
341
Loc.
Lewis Run, PA
Another possibility would be to match the fan angle with the angle of the radiator and support, if that makes sense.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Who are you going to believe..him or your own lying eyes?;D
You don't have to believe either - just sketch it out in any CAD program, and rotate the engine/trans/t-case assy. so you can check the d'shaft angles for each configuration. I think we can all agree that no one would try to raise the engine through the hood, or lower it through the welded xmbr, so the pivot axis would be the line thru the engine mounts, and it would be the trans mount/bolted xmbr that would get moved.
...match the fan angle with the angle of the radiator and support, if that makes sense.
Not really, since it assumes the radiator angle is critical (it isn't) AND that it's mounted perfectly, and that the core support is at the perfect angle, and that the body mounts haven't shifted or sagged or been lifted.

There's some limit at which the oil system stops working correctly (mainly in the splash areas, and the head pressure at the main seals), but it's probably close to 30°. Otherwise, there's no particular "best" angle for the engine. It's all about the driveshaft/u-joint flex angles.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
I still don't believe you Steve.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
here's one I've never had to worry or at least never had access to verify. Talk about front to rear angle, how about lean left or right as the engine sits on the engine mounts? Anyone seen that? I've never noticed this before but with the body off it's easy to note at least my motor leans a little left low. I tried pulling and jacking and nope, that's where it sits, securely attached to tranny and tranny mount.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
You don't have to believe either - just sketch it out in any CAD program,.

err..does having actually done it for real in the shop count too? I mean..I'm a mechanical injuneer by trade..and have Solidworks and Rhino on my desktop, but nonetheless I still did the same thing that Bax did; I assembled the entire driveline on the frame and played around with the rear mount height.;)
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Did you take pics? If it's not much trouble, how about sketching it up for us? Should be pretty easy to draw, especially if you reduce it to a simple triangle: the engine mount would be the top/front(left) point; the front diff's rear u-joint would be the lower/mid point; and the t-case front output u-joint would be the top/rear(right) point that moves in an arc centered on the engine mount. All you'd have to do is track the t-case angle (which would be slightly less than the upper side's) and figure the relative angle to the front d'shaft (lower side).

I could draw it, but bax wouldn't believe me anyway. :D
 
Top