• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

FiTech EFI pre-order info

BigB

Contributor
Sr. Member
Joined
Nov 19, 2011
Messages
499
Wish they would offer a group buy now that they are selling through others seems like it would work.

Can't see them offering a group buy when they seem to be flying off the shelf. I hope they do eventually, so I can get another.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Question for ya Kyle...how come you're thinking of going away from stock SEFI stuff?

Sorry I missed this-

I'm switching to a 11:1 compression 351w that I'm planning on putting ~150 shot of N20 on and I can't easily do that with EECIV with mail order tunes. FiTech is basically OBDII with all the info and I like that I can restrict the N20 to only come on a certain RPMs, coolant temps and AFR's.

Added benefits on top of easily running my radical engine are a much shorter engine that will fit under a hood, more clearance for master cylinders and a much simpler and more adaptable package.

I could theoretically pull this system off my Bronco and throw it on my 66' Galaxie 500 and cruise around town when I'm not 4 wheeling as well- just buy an extra wiring harness and its as simple as a carb swap.

;)
 

bsquared

Contributor
Sr. Member
Joined
Dec 4, 2010
Messages
972
BullPucky
http://67-72chevytrucks.com/vboard/showthread.php?p=7441193#post7441193
If you read majority of this thread it's about him having problems with cold starts and how it dies after a cold start.
AND he's been in contact with FiTech the whole time.

Swampbog, I read most of this thread and it was very informative. Mine is running with an MSD AL6 box controlling the timing and a MSD 3 wire distributor, so I have it wired up like their installation instructions dictate. However, Ray1970 clearly states he's running a 3 wire ready to run dizzy converted to a 2 wire and locked out. Anyone got an idea on how to wire this? Their installation instructions say this can't be done and he's saying he talked to tech and it can be done. Delete the ground from the 3 wire and hook it up as a conventional 2 wire dizzy?

From the previous posts it seems like the FI Tech unit does a better job of controlling the timing and I'd like to see how the FI Tech unit runs with it controlling the timing. Anyone know the procedures for locking out a 3 wire dizzy, helping it work with the FI Tech unit and how to wire it up? Phase it in?!

I really don't want to change out a perfectly good dizzy and am curious how the 3 wire is changed to a 2 wire.

Help is appreciated 'cause I think my unit could be running a LOT better than it is. (but it is running)

Cheers, B2
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
re-setting to factory

If for whatever reason you may want to reset to factory and start over. from Bryce:

"Go to Write Cal To ECU and select the file named DEFAULT T195. Load it and that will be back to factory."

From Bryce @ Fitech
 

TDubya

Sr. Member
Joined
Aug 3, 2009
Messages
381
Loc.
Fortuna, CA
I noticed today that if you ordered the 400hp Go Street EFI from Jegs today it would ship out on Feb. 12. Still no update on FiTech's website.
 

377

Sr. Member
Joined
Aug 24, 2012
Messages
372
Loc.
The Bluegrass State
I ordered one from Summit since they are closer to me. At first they showed a 2/10/16 ship date but now it is showing a 4/7/16 arrival date not sure what that is about. Keep us posted if you get yours in the near future. I will cancel my Summit order, Jegs isn't close to me but it will beat th hell out of a two month wait!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If anyone is needing one of their #30001 or #30002 600hp kits, we have a few in stock right now.
Not on the website just yet, but our part numbers are #6630 and #6632 respectively.

Sorry for the not-too-shy sales pitch, but if you have to wait a couple of months this might be an alternative. Maybe that's just for the 400hp kits?
And I wanted to let members here know that we were a distributor for them now too anyway, so this was as good an opportunity as any.

Paul
 

mritchy1

Full Member
Joined
Nov 22, 2009
Messages
166
Do you have the fuel command center is stock also, I am getting ready to purchase this system and just assume get it from you guys
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Thanks! Appreciate that. Don't think we have them, but it'd be worth a call in tomorrow to check.
Looks like we're stocking the standard fuel delivery kit, but I did not see the command center for some reason. Maybe I didn't catch the right numbers, which is why it'd be worth a quick call. I would think we'd definitely want that in stock!

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And as a little side note, we noted a good thing with the FiTech system. Apparently their programming is a little more compatible with bigger cams (or mismatched components?).

Justin just installed one on his '72 (which means he's now tried the E-Street, Atomic, and now the FiTech on the same engine) and it seems to settle down quicker, idle better and produce less exhaust smell (a little bit less anyway;D) with his pretty lopey cam and dual-plane Performer manifold. Too bad we don't have specs on his PO-installed cam, but it's decently hot.
Seems like the manifold might be a mismatch for the cam too, being a low-rise dual-plane. Which could have played a little game with balance and tuning, but the new setup seems more capable of dealing with it.

The Atomic ran great, and still runs perfect on Johnny's (mild stock-ish cam), but this one just seems, a little smoother on Justin's.

Thought you guys might like that little bit of user feedback to add to your brains.

Paul
 

pipermike

Full Member
Joined
Oct 9, 2010
Messages
253
This is quickly heading to the the top of the list for my next purchase l'm about fed up with my carb set up. Glad to see one our vendors getting involved with it. It would be cool it there was a way to match your Sherman tank kit with this to illiminate the fuel command center.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Do you mean to eliminate the separate module? Or to eliminate the cost of the additional stuff?
To get rid of a stand-alone separate module, it would have to be in the tank, but it would still be there adding to the cost and complexity.
To get rid of the additional cost, it's already done. You just have to add your own return line. The rest is done for you with the EFI version of the Sherman. All of the tanks come with a return port, and the EFI models already have the in-tank pump. If you have an existing Sherman, it's as simple as adding the EFI kit to convert it.
Pretty much that's it, unless I'm missing what you're saying.

The whole point of setups like the Command Center, if I'm not mistaken, is to avoid, or simplify plumbing a return line, to avoid having to add an in-tank pump, and to create a small reservoir such as you have with low-pressure/high-pressure sump setups.
About the only way I can think of to avoid a return line is by either not using one, using a variable control computer for your pump, or having something like the Command Center. Either internal or external.
Companies like Edelbrock, FiTech, Aeroquip and others make something along those lines already, but if you have a better idea that's simpler, that would be great!

Personally, I like a full return line anyway, just to keep all the fuel at the engine cooler. Probably not really needed for most, and just a throwback from carburetor days, when cool fuel was even more important. I still like more than just the pump to benefit from cooler fuel though.
Since all Shermans already have a port for a return line, and the EFI version already has an in-tank pump, I'm not sure how we would change it without ending up creating our own Command Center clone.

If you were thinking along different lines, let us know and we'll throw it around.
If it's not too much trouble, it might be something worth further digging.

Thanks

Paul
 

pipermike

Full Member
Joined
Oct 9, 2010
Messages
253
I guess I was just thinking out loud and asking a question at the same time. :) The command center adds 395$$ to the cost and basically gives you a little thermos of gas under the hood that the high pressure line draws out of,I follow that, but in the big picture of Bronco restoration for about 240$$ more I can buy the Sherman tank EFI complete & upgrade to a bigger tank at the same time. I think you answered my question, just run a return line back & wire the pump in the tank back to the EFI unit? Am I on the right track?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yep, you got it.
Other than the extra work of adding the new tank, you're only talking about the line(s) in addition to that.
The existing feed line "could" be used if it's in good shape, but it depends on how it's set up now. No matter which way you do it, if you're still stock and carbureted, you will have to do at least some minimal re-routing of it up near the engine compartment.
If you're still carbureted with a stock type pump, you would bypass that and go straight to the inlet on the new throttle body.
Then the return line would run back to the tank.

Typical setups use 3/8" line for the feed, and 5/16" for the return. But that's just common practice, not etched in stone stuff. Either size will work for both if you want, unless your engine is putting out more than 300 to 350 hp, in which case the 3/8" is a better choice.
Using a smaller return is good practice simply because it creates it's own restriction at the transition, thereby helping to keep a more consistent reservoir of fluid ready and waiting at the injectors. Which is why they put the regulator at the output side of things on factory setups as well.

I haven't worked with a FiTech yet, and only glanced at Justin's yesterday at the shop, but I believe it uses a built-in regulator, which probably means there is a return port right no the TB unit itself.
Should be pretty straightforward.

Of course... I should probably read the instructions and details before I start spouting off like I know stuff!

Paul
 

work765

Full Member
Joined
Aug 27, 2015
Messages
279
You guys running these. Are you getting better gas mileage? Noticeable?
I drive mine daily and it's carbureted. Im wondering how much I would benefit
 

Justin@WH4x4

Sponsor/Vendor
Jr. Member
Joined
Oct 3, 2013
Messages
104
I have noticed fuel mpg increase, but not sure to what degree due to the fact that my Bronco is not my daily driver. I run the Sherman Tank with an In Tank pump and a return line. The Throttle body is designed to use the optimum amount of fuel in all situations, no more or less. It burns cleaner, doesn't run rich like it used to with a carb, and excess fuel travels from the throttle body return line back to the tank. Very happy with the results of this unit, and have been driving my bronco daily since the install.
 

drock

Sr. Member
Joined
Aug 11, 2012
Messages
492
I have noticed fuel mpg increase, but not sure to what degree due to the fact that my Bronco is not my daily driver. I run the Sherman Tank with an In Tank pump and a return line. The Throttle body is designed to use the optimum amount of fuel in all situations, no more or less. It burns cleaner, doesn't run rich like it used to with a carb, and excess fuel travels from the throttle body return line back to the tank. Very happy with the results of this unit, and have been driving my bronco daily since the install.

Justin,

Did you ditch the Edelbrock E-Street set up? Any problems with it?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
He can fill in the details, but he's experimented with all three now. E-street first, Atomic next for the last few months, and now the FiTech just since last week.
Varying degrees of satisfaction with each, and frustration with some, but so far the FiTech seems to be the best at working with his big cam and low-rise intake. At least that's what my theory is on the differences.
The Atomic was a next best, running well but never finding quite the right mix. Ran good, just wasn't perfect. The E-street was the most finicky (also the first try at EFI for him).
If I remember, his engine has never really run quite perfect. Even with the carburetor the exhaust smelled rich. Each experiment with TBI has run noticeably smoother than the previous, but still not perfect. But this one's sounding pretty dialed.
I would say for him the FiTech is the best so far with his combo. At least as judged on the smiles-per-mile-o-meter when he showed up for work yesterday!
But don't expect Johnny to change out his MSD anytime soon. His is running too sweet to mess with. He hasn't even wanted to change the idle, or experiment with air/fuel ratios, or timing or anything. Runs too good as is.

I don't know this next bit for a fact, but any of them could have suffered from a combination of the big cam, and low-rpm based dual-plane manifold and TBI combination that Justin's got. Apparently some engine and TBI combinations prefer an open plenum.
Did anyone else see the post in another thread last week (I think?) where David Freiberger did some YouTube dyno tests with a throttle body EFI setup on both dual plane and single plane intakes? They determined that the single plane was definitely more compatible with this type of EFI setup. At least on that engine.

Counterintuitive for the mild cam crowd like me, and it wasn't like the EFI would not run on the low-rise intake. Just that the open plenum and longer runners of the single plane intake seemed to keep the the engine happier and the TBI setup mixing things more effectively than not. Add a big cam, and who knows what's going to happen.
Now I'm wishing I'd stuck to my guns and not sold that old Holley Z-series Street Dominator manifold I had!!!! Be fun to experiment between my Edelbrock Performer and the Holley Z.

Anyone know where that link is by the way? I could not find it to show Justin yesterday.

Paul
 

Justin@WH4x4

Sponsor/Vendor
Jr. Member
Joined
Oct 3, 2013
Messages
104
Justin,

Did you ditch the Edelbrock E-Street set up? Any problems with it?

The Edelbrock ran great when I first put it on, but began giving me issues within the first 3 months or so. It would die on me after about an hour of driving, then it would take an hour or so before I could fire it back up again. Edelbrock said that my HEI that I had been running wasn't giving out a good enough tach signal. I explained to them that I hadn't changed anything in the equation and it ran great for the first few months, but they told me to change out the module with an MSD Module that has it's own dedicated tach wire. $100 later that solved the issue, but it still ran rich and stunk like unburnt fuel while running. I sent the E-Street back, and purchased the MSD Atomic. I've ran the Atomic for the last year and half. It has been a great unit, and I didn't have any complaints regarding it. The only reason that I was willing to change it out to the FI Tech was because of the positive things that I had been hearing about it, and the fact that Wild Horses was becoming a distributor, so it made sense to get it on one of our rigs to test it and gain some knowledge of the system to help sell the product. The simplicity of the FI Tech kit, the features like the built in fuel regulator, the built in ECU, Internal GM Based Parts that can be replaced over the counter from any parts house, and the price were all selling points to me, so I decided to give it a shot. This kit hands down has outperformed any other kit that i've ran on my motor. The only thing that needed adjustment from the moment that I installed it was the idle screw. I backed it out a turn and have been driving daily ever since. Pretty awesome setup in my opinion, and the price point is awesome.
 
Top