• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Carb Questions

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Like many others here, I'm a big fan of the 2100 Autolite and 2150 Motorcraft carbs.
The only problem I had with my factory 2150 was after I re-geared from the factory 3.50s to 4.11s.
While passing, when the tranny kicked down into second, I couldn't get around the car I was passing. The little carb would just plain run out of air!
The fix was to replace it with a bigger 2100 from a '69 Torino 390, along with a bit larger 2.25" exhaust and catalytic converter. Big difference!
That mod went totally undetected in the CA emissions testing while I lived in CA. ;)
I always thought one of those two barrel Holleys would be a good candidate. I'd play with it a bit more.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Yes, 5 speed manual.

Is this the vacuum port you're talking about?

Do I just cap it off?

oyo6OfFh.jpg
 

pipeline010

Sr. Member
Joined
Nov 15, 2017
Messages
618
I know Im not the guru around here, but isn't this guy's PCV just sitting there without a hose in it? I'm guessing that empty manifold port is supposed to have a linkage to your pcv that someone yanked. If that port is from the holley base plate it seems reasonable to me.

So ya, step one plug your holes.
Step two check your timing, following advice above.
You don't go tuning a carb until everything else is straight. But you've just got to have sucking sounds all over that manifold.
 

pipeline010

Sr. Member
Joined
Nov 15, 2017
Messages
618
Looks like your baseplate hose is going into your oil fill cover. That's the one that should be on your pcv grommet. Does your air filter have a hose attachment port? That's the one I use on my oil cap. I'm not sure any of that is a hard or fast rule, but I've heard from multiple sources the baseplate should be ported to the pcv.
 

Bronco 4 life

Jr. Member
Joined
Sep 11, 2017
Messages
89
Loc.
Yakima
This is the port to start with go to the parts store and get the rubber vacuum plugs in the help section
 

Attachments

  • 52243C5D-2C07-49BA-B5D3-94757A27F1FD.jpg
    52243C5D-2C07-49BA-B5D3-94757A27F1FD.jpg
    48.8 KB · Views: 41

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Yes, 5 speed manual.

Is this the vacuum port you're talking about?

Do I just cap it off?

oyo6OfFh.jpg

No, that photo shows the open nipple on the EGR vacuum canister. It's hiding the open nipple on the vacuum tree.

Your photo #8 shows the open nipple on the vacuum tree right under the EGR vacuum canister.
 

AC932

Full Member
Joined
Sep 17, 2018
Messages
254
Looks like your baseplate hose is going into your oil fill cover. That's the one that should be on your pcv grommet. Does your air filter have a hose attachment port? That's the one I use on my oil cap. I'm not sure any of that is a hard or fast rule, but I've heard from multiple sources the baseplate should be ported to the pcv.

Nah, pretty sure he's got it right, assuming that loose elbow attaches to his air cleaner. If you don't have a PCV pressure regulator thingy, then it probably doesn't matter, but if you do, then it should have vacuum on it. Since that pressure reg would be on the oil cap, then you'd attach that to your carb base.

Jzzrl7y.jpg


Also, as far as vacuum plugs, make sure what's already on there actually works. Found out all that three of the plugs the PO put on were the wrong size, add that to the broken vacuum retard diaphragm and I had a pretty bad vacuum leak.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
So yeah, the oil filler PCV looks like it goes to the base of the carb. The passenger side PCV is just capped off with that elbow, shouldn't that go somewhere?

I plugged the vacuum on the tree under the EGR canister. Will fire her up and see if theres any difference now but I'm also curious about my PCV system now.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
OK I capped that vacuum port and put new spark plugs in and already huge improvement.

Idles without stalling and throttle response and power are improved.

It still gets bogged down at full throttle. There's a sweet spot on the pedal where it wants to be but it feels like its too rich at WOT.

I still intend to try and check/set my timing.

Other thing I noticed is that both PCV fittings are quite loose. The elbow cap on passenger side rotates freely and wiggles around, and oil filler cap doesn't seal well and the PCV valve on that side easily pulls right out.


Best next steps?
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi read my post 18 again.
Post a couple of pics of the old spark plugs.
They may show a rich running engine.
I would drive and go through a couple of tanks of gas and check the plugs again.
Just curious as to which air cleaner you run. Some are more restrictive than others.
I think you can do this. Good luck
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Here's some photos of the old plugs below.

My air filter is just some generic unit. Open to suggestions on something of better quality.

I'll do a few tanks and pull the plugs again.

And yeah, I can do it. Just a learning process but you guys are all incredibly helpful so thank you! Way more gratifying to figure it out and DIY.


0IEZQARh.jpg


DcjnWoBh.jpg


EEg8xx2h.jpg


uOzrDXUh.jpg
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
So yeah, the oil filler PCV looks like it goes to the base of the carb. The passenger side PCV is just capped off with that elbow, shouldn't that go somewhere?

I plugged the vacuum on the tree under the EGR canister. Will fire her up and see if theres any difference now but I'm also curious about my PCV system now.

The PCV system provides a metered amount of air to the mixture. With the "air-in" side capped off on your passenger side valve cover, you're not letting any air in.
This will affect the mixture idle, cruise and even full throttle a bit.
 

Attachments

  • PCV-valve.jpg
    PCV-valve.jpg
    161.8 KB · Views: 34
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
The PCV system provides a metered amount of air to the mixture. With the "air-in" side capped off on your passenger side valve cover, you're not letting any air in.
This will affect the mixture idle, cruise and even full throttle a bit.

I have been wanting to install a new valve cover kit, partly for dress up looks and also to get some new gaskets and better gear on there.

When I do so, should I move the existing hose on my filler cap to the passenger PCV, and then cap or install one of those filter caps on the drivers/oil filler side?
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I have been wanting to install a new valve cover kit, partly for dress up looks and also to get some new gaskets and better gear on there.

When I do so, should I move the existing hose on my filler cap to the passenger PCV, and then cap or install one of those filter caps on the drivers/oil filler side?

Your photo shows the PCV valve on the driver's side connected correctly.
The fitting on the passenger side valve cover is just a plastic elbow. It should be connected to a clean air source (usually on the air cleaner) with a hose.
I believe, through the years, the side that had the PCV valve and the side that had the elbow has changed. That's not important in function though.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Your photo shows the PCV valve on the driver's side connected correctly.
The fitting on the passenger side valve cover is just a plastic elbow. It should be connected to a clean air source (usually on the air cleaner) with a hose.
I believe, through the years, the side that had the PCV valve and the side that had the elbow has changed. That's not important in function though.

Ok, so I think I will go ahead and get the new valve cover kit and new air cleaner to refresh everything, add new gaskets, and get the PCV routing correct. My current air cleaner doesn't have an inlet for anything.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
It still gets bogged down at full throttle. There's a sweet spot on the pedal where it wants to be but it feels like its too rich at WOT.

Is this full throttle at any time? From idle and while cruising? A bogging often indicates an over-lean condition instead of rich.
And your spark plugs are definitely NOT fouled with unburned fuel or all sooted up. Too rich and they'd be darker in color, to all the way black.

I still intend to try and check/set my timing.

Definitely this. Checking timing is always part of tracking things down.
So is how your vacuum advance is connected.

And while using the timing light, check not only base timing at idle, both with the vacuum hose disconnected AND connected, but check what the timing does as you raise the rpm with the throttle lever.

Other thing I noticed is that both PCV fittings are quite loose. The elbow cap on passenger side rotates freely and wiggles around, and oil filler cap doesn't seal well and the PCV valve on that side easily pulls right out.

While they were never really perfect, they should at least seal somewhat well. Sounds like your rubber grommets have met their match with the years and heat cycles. Probably hard to get out to replace with new ones too due to how hard they are.
See if you can get new ones at the local parts store, or see if your new valve covers come with new grommets.
Make sure the covers you choose both have ports in them too, just like the stock ones. Unless you have a Ford fuel-injection intake manifold, you need both so you can keep the valve in one and the breather in the other.

Air cleaners often have a knock-out in the base (look underneath yours to see if there is a round half-cut plate you can remove) and you can purchase an elbow that fits the knockout. This would be your best breather.
The problems come with our engines when the hole is somewhere that interferes with something else. Carburetor linkage, and stuff like that.

Paul
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Is this full throttle at any time? From idle and while cruising? A bogging often indicates an over-lean condition instead of rich.
And your spark plugs are definitely NOT fouled with unburned fuel or all sooted up. Too rich and they'd be darker in color, to all the way black.



Definitely this. Checking timing is always part of tracking things down.
So is how your vacuum advance is connected.

And while using the timing light, check not only base timing at idle, both with the vacuum hose disconnected AND connected, but check what the timing does as you raise the rpm with the throttle lever.



While they were never really perfect, they should at least seal somewhat well. Sounds like your rubber grommets have met their match with the years and heat cycles. Probably hard to get out to replace with new ones too due to how hard they are.
See if you can get new ones at the local parts store, or see if your new valve covers come with new grommets.
Make sure the covers you choose both have ports in them too, just like the stock ones. Unless you have a Ford fuel-injection intake manifold, you need both so you can keep the valve in one and the breather in the other.

Air cleaners often have a knock-out in the base (look underneath yours to see if there is a round half-cut plate you can remove) and you can purchase an elbow that fits the knockout. This would be your best breather.
The problems come with our engines when the hole is somewhere that interferes with something else. Carburetor linkage, and stuff like that.

Paul

Thanks!

Yeah, I expected the plugs to look different but obviously not suffering from a rich mixture.

I'm not sure I understand your question about WOT, but yeah basically anytime I go past the sweet spot on the throttle it just makes noise and goes nowhere. I'd say it likes to be at about 50-60% throttle to go full blast. Anything beyond that and it bogs down.


I was just thinking to get a new valve cover kit form wildhorses: https://www.wildhorses4x4.com/product/Valve_Cover_Kit/bronco_Valve_Covers

These have the PCV port on the passenger side, and also the small air filter attachment that goes on the oil filler cap. I assume these will work...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sounds like you're lean bogging, or don't have sufficient ignition advance then.
Could be anything from needing more accelerator pump squirts, larger main jets, different adjustments, re-adjust the timing, etc.
Just fine tuning all aspects.

Even the wrong PCV valve will lean out the mixture by too much. Yours almost sounds that way, but when I experienced it, it really was not at higher throttle settings. It bogged down anytime I tried to take off from a full stop. More throttle and it usually caught up eventually.
 
Top