• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Carb Questions

OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Sounds like you're lean bogging, or don't have sufficient ignition advance then.
Could be anything from needing more accelerator pump squirts, larger main jets, different adjustments, re-adjust the timing, etc.
Just fine tuning all aspects.

Even the wrong PCV valve will lean out the mixture by too much. Yours almost sounds that way, but when I experienced it, it really was not at higher throttle settings. It bogged down anytime I tried to take off from a full stop. More throttle and it usually caught up eventually.

All noted, thanks.

I believe I'm on the right track. After capping that small vacuum port and adding new plugs it runs 10x better already. I suspect I still have some vacuum leakage from loose fittings, so I'll just go ahead with valve covers, gaskets, and new PCV fittings, then check timing and go from there.

Thanks again to everyone for their help.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
If it still has a lean bog after you set the timing you should check your float level, could just be running out of fuel. It's easy to check and adjust on that Holley.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
I'm beginning to think that vacuum leaks might be my #1 source of my issues.

I replaced 2 other caps last night that were brittle and cracked. One fell apart when pulling it off it was all dried up.

Top dead center is lined up with the #1 cylinder wire on my distributor and the cap looks good on the inside. I should have a minute to get her running this afternoon to see if my performance at WOT is improved now with these vacuum ports properly capped.


XiQPlXQh.jpg


Y0AZtN9h.jpg


Rlxqcwih.jpg


61TETmfh.jpg


YHwtUjVh.jpg
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I replaced 2 other caps last night that were brittle and cracked. One fell apart when pulling it off it was all dried up.

Glad you changed those. An all too common issue these days. In fact, the any new ones you get are likely to last anywhere from 3mo to about 1yr. Probably no more than that.
If you can find some from the dealer, or relatively new-ish ones at a junkyard, I think you're better off.
Unfortunately this makes the old "bolt-in-the-hose" method seem the best route to take. At least the fuel rated hose lasts for a goodly long time still. But the rubber and plastic and poly caps seem to be made out of petroleum-susceptible stuff.

Top dead center is lined up with the #1 cylinder wire on my distributor

That's usually a method to just get close enough to start. But if it does not fire up right away, don't hesitate to rotate the distributor by hand until it does. If you have a timing light, using it immediately would be a good thing.
And for all this, leaving the clamp bolt semi loose for now might be a good thing.

...and the cap looks good on the inside.

I'm not sure I agree. Maybe no visible cracks or failing bits, but it sure looks well used and carbon traced/scored in an unusual pattern.
I see you have the "small" Dura Spark cap and rotor still. Ford did not keep that for more than a year or so, until they upgraded to the "large" cap.
I would make a point that, if you're not going to replace it now, then the next time you need new plug wires, just replace the wires with the new style and replace the cap and rotor with the larger ones. You'll need the "cap-a-dapt" part, but it clips right on to your existing distributor using the stock clips.
You can buy them new just about anywhere I think, or score one in the junkyard.

But if it was me, and once I started it up if it runs rough like it needs a tune-up, I'd be replacing that cap and rotor even if with just the same style. Just looks pretty well used.
Did you clean the faces of the contacts while you were in there?
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Glad you changed those. An all too common issue these days. In fact, the any new ones you get are likely to last anywhere from 3mo to about 1yr. Probably no more than that.
If you can find some from the dealer, or relatively new-ish ones at a junkyard, I think you're better off.
Unfortunately this makes the old "bolt-in-the-hose" method seem the best route to take. At least the fuel rated hose lasts for a goodly long time still. But the rubber and plastic and poly caps seem to be made out of petroleum-susceptible stuff.



That's usually a method to just get close enough to start. But if it does not fire up right away, don't hesitate to rotate the distributor by hand until it does. If you have a timing light, using it immediately would be a good thing.
And for all this, leaving the clamp bolt semi loose for now might be a good thing.



I'm not sure I agree. Maybe no visible cracks or failing bits, but it sure looks well used and carbon traced/scored in an unusual pattern.
I see you have the "small" Dura Spark cap and rotor still. Ford did not keep that for more than a year or so, until they upgraded to the "large" cap.
I would make a point that, if you're not going to replace it now, then the next time you need new plug wires, just replace the wires with the new style and replace the cap and rotor with the larger ones. You'll need the "cap-a-dapt" part, but it clips right on to your existing distributor using the stock clips.
You can buy them new just about anywhere I think, or score one in the junkyard.

But if it was me, and once I started it up if it runs rough like it needs a tune-up, I'd be replacing that cap and rotor even if with just the same style. Just looks pretty well used.
Did you clean the faces of the contacts while you were in there?

Thanks for the info on the caps--I'll make sure to check them regularly to avoid any more leaks.

Regarding the distributor, I didn't do anything other than line up '0' on the harmonic balancer with my timing pointer, then pulled the cap off to make sure it was lined up with the #1 plug wire. I haven't done any actual timing adjustment other than that.

I'd like to install a new MSD distributor and new plug wires sometime this year. I'm always motivated partly by performance and also by dressing up the engine bay. Maybe in the meantime it makes sense to put a new cap and rotor as you suggest, and spend the bigger money on a new distributor next winter.

Anyways--I'll pull her out of the garage this evening and see how she's running with the new vacuum caps and go from there. New valve cover kit arrives tomorrow so that's my fun DIY job for tomorrow night.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, since you are looking at the distributor you can check the vacuum advance for leaks. Remove the hose at the carb and suck on it. You should see the breaker plate move, which shows it is advancing the timing..
Your cap shows arcing wear in the plastic.
Going to the bigger Ford cap is a good idea, but then you need new wires. Too much money if you plan on changing the ignition. But the Ford Duraspark is a very good ignition system, and most of the replacement stuff is import. Personally, I would keep the Ford parts.
Also the spark plugs look pretty good, I expected to see much worse.
Good luck
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Hi, since you are looking at the distributor you can check the vacuum advance for leaks. Remove the hose at the carb and suck on it. You should see the breaker plate move, which shows it is advancing the timing..
Your cap shows arcing wear in the plastic.
Going to the bigger Ford cap is a good idea, but then you need new wires. Too much money if you plan on changing the ignition. But the Ford Duraspark is a very good ignition system, and most of the replacement stuff is import. Personally, I would keep the Ford parts.
Also the spark plugs look pretty good, I expected to see much worse.
Good luck

Is this the right size larger cap? https://www.cjponyparts.com/distributor-cap-female-v8/p/DC2/
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, your link is for the original replacement cap.
Look at the 79 or 80 cap which is larger. The larger cap has wire terminals that looks like the end of a spark plug, and needs the corresponding wire set. The larger cap needs a lower adapter to fit the distributor. There are 2 pieces. You buy the lower once, and replace the top as needed.
The advantage to the larger cap is as the secondary (coil) voltage increased in the Duraspark ignitions, there is s tendency for the spark to scatter and jump in the small cap. So Ford enlarged the cap to separate the terminals and eliminate the spark scatter problem.
If you don't know how old the spark plug wires are, and you decide to keep the Duraspark ignition, you may as well upgrade to the larger 2 piece cap, rotor, and wires.
Good luck
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
This is my #4 header exhaust. It's the only one that has a build up of black gunk around it. Is this showing signs of something yucky going on inside the cylinder?

23HP6Nf.jpg
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, your spark plugs indicate what is going on in the cylinders, and #4 looks good.
That small black crud is either a very small drip from the valve cover, or a very minor exhaust leak.
I would gently snug down the valve cover bolts.
I would leave the exhaust alone for now.
Good luck
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Hi, your spark plugs indicate what is going on in the cylinders, and #4 looks good.
That small black crud is either a very small drip from the valve cover, or a very minor exhaust leak.
I would gently snug down the valve cover bolts.
I would leave the exhaust alone for now.
Good luck

Thanks...actually installing new valve covers and new perma dry seals tonight, so that should solve that problem.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Check the plug gap. With the small cap you have, try .045 gap, the same size as the shank of a 3/64 drill bit or #55 drill bit. Gap much wider than that you need the larger distributer cap and rotor. By looks of the picture the gap is much wider than that.
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Reporting back with some positive news....

I got the new valve covers (with new permadry gaskets) installed late last week. The PCV hose now runs from the passenger side to the bottom of carb and the oil filler cap has a clean air filter on it. Found TDC and set timing with a friend's timing light to somewhere between 10 and 14 degrees advance. It's also advancing itself to around 30 degrees with higher RPM.

The timing was actually pretty close to 10 degrees already, but I did advance it slightly and it seems to idle better and definitely runs way better through the power range. I am not sure if maybe I had a vacuum leak from the old valve covers as the bolts were not that tight and some came off with no effort at all.

So, I have done the following:
- Plugged vacuum leak
- New spark plugs
- New valve covers and gaskets
- Re-routed PCV hoses
- Cleaned up distributor and set timing

I don't know if it was one of these things or a combination of all of them, but it's running wayyyy better now. I think it can get better but I am a happy man for now.


BUT....here is a new conundrum...

I pulled the vacuum hose that connects my carb to my distributor and plugged in a vacuum gauge and....no reading. Put my finger on the vacuum port (on the carb) and felt no suction at all. What am I doing wrong? The distributor is working and it advances like it should with high RPM but there is no vacuum??

sx7WgQCh.jpg


EDBd81Ch.jpg
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
You probably found the ported vacuum source...the one that has no vacuum until the throttle plates open some. That's the one the the distributor is typically plumbed to.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
What he said.
You can easily check it though, by hooking up the gauge again and opening the throttle slightly by hand. Should start to react very quickly with just a little movement of the throttle lever.
If that happens, then you know you were on the ported vacuum fitting and that it's just doing it's job properly.
There should be another port you can find to put the gauge on to give you straight manifold vacuum even at idle.

By sealing the valve covers you did not get rid of what would be considered a traditional vacuum leak. Any vacuum in the crankcase and rocker gallery is created by the PCV valve and is sort of a "controlled vacuum leak" so to speak.
So while it is a bit of a potential leak, it's more in the way of letting unfiltered air into the engine than it is going to effect your idle in any way.
That said, if you have enough of those leaks, including loose fitting rubber grommets for the valve cover fittings, eventually you can get enough leakage to effect idle slightly.
But it's still the other vacuum leak spots that cause more trouble at idle.

Paul
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Got it, thanks guys.

Is it right to have the distributor on a ported vacuum source? Or should I run it to manifold vacuum instead? It must have some affect on idle and total timing, doesn't it?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Stock distributer uses ported vacuum. Some non stock performance distributers use manifold vacuum but they have to be built special to use manifold vacuum.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Many later smog control era vehicles used full vacuum too, but it was controlled through a maze of temperature controlled valves and all sorts of other wizardry.

While I have always found ported vacuum to work best for me, there are plenty of people running straight full vacuum advance too, with very good results. So my advice is always to at least try both, but start with ported to get a baseline.
Your idle tuning will change for each too, so base timing, carburetor idle settings, etc will change for both.

Paul
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, you can verify the ported vacuum is working by using the vacuum gauge and open the throttle. You should see high vacuum at steady RPMs. Good luck
 
OP
OP
J

Jc.av8r

Sr. Member
Joined
Jun 3, 2014
Messages
400
Thanks guys. At this point I intent to upgrade my distributor and spark plug wires anyways, so I'll tinker and play with options a bit once I do that. For now everything is vastly improved so I'll drive it as it for the time being.

So many thanks to everyone for their help as I try to advance form Bronco noob to Bronco DIY capable. I love this forum!
 
Top