• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Pcv/vent

OP
OP
MonsterBIlly

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
Here is the Snioer I have. https://www.summitracing.com/parts/...qkV7-ScaPa2Wm-KnclN49KkpP6AhxpqRoCde8QAvD_BwE

I think I found the issue. I switched out the pcv to a different unit. While it was idling I pulled the pcv from the valve cover and it was being pulled fully open by vacuum. I assumed at idle it SHOULD NOT be fully opened. So I had another pcv laying around so I swapped it. The new one I out in was not fully open when idling. It was barely open, pretty much closed at idle. This corrected the lack brake vacuum and all is working okay right now. I'm still getting a small amount of oil mist blowing out of the vent but much better than it was.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
There is a plugged port on the base of the sniper that appears to be vac but nothing in the manual states what it for.
I also dint know if I use it for brakes or pcv if it will effect the other as the tee does.

Is this the port you mentioned? If so, yes you can use it for the PCV valve. The two large ports won't affect each other, as Paul mentioned.
Its probably 1/4 NPT, so this fitting will screw right in and you're all set https://www.napaonline.com/en/p/NTH90542
EDIT: It definitely leads to full manifold vacuum.
 

Attachments

  • Sniper.jpg
    Sniper.jpg
    68.3 KB · Views: 41
  • Sniper2.jpg
    Sniper2.jpg
    82.1 KB · Views: 45
  • Sniper3.jpg
    Sniper3.jpg
    39.6 KB · Views: 47
Last edited:

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Thanks, I like how you did that.

Thanks, nice and clean, and the wires don't make contact with anything other than the wire separators.

Here is the Sniper I have. https://www.summitracing.com/parts/...qkV7-ScaPa2Wm-KnclN49KkpP6AhxpqRoCde8QAvD_BwE

I assumed at idle it SHOULD NOT be fully opened.

Just the opposite, should be fully open at idle. Did you see my post 2 posts ago? Holley gave you the option for adding a 3/8 port at the front of the Sniper, perfect for the PCV.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Is this the port you mentioned? If so, yes you can use it for the PCV valve. The two large ports won't affect each other, as Paul mentioned.
Its probably 1/4 NPT, so this fitting will screw right in and you're all set https://www.napaonline.com/en/p/NTH90542
EDIT: It definitely leads to full manifold vacuum.

That port sealed with thread sealer, don't use that. The little hole in that chamber is the MAP sensor. That chamber is what balances the MAP reading so a divided plenum intake works with the Sniper.

Why is that port there? External boost reference. Running a roots blower, that can be setup to read the boosted manifold pressure by blocking the ports to the throttle bores and running an external boost reference line.

Connecting PCV will drop the MAP reading as you feed air into the MAP sensor.

There is an offset (but evenly distributed) 3/8 vacuum fitting on the rear of the throttle body, use that for PCV.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
That port sealed with thread sealer, don't use that. The little hole in that chamber is the MAP sensor. That chamber is what balances the MAP reading so a divided plenum intake works with the Sniper.

Why is that port there? External boost reference. Running a roots blower, that can be setup to read the boosted manifold pressure by blocking the ports to the throttle bores and running an external boost reference line.

Connecting PCV will drop the MAP reading as you feed air into the MAP sensor.

There is an offset (but evenly distributed) 3/8 vacuum fitting on the rear of the throttle body, use that for PCV.

Bummer, he's using that one for his brake vacuum booster and tee-ing the PCV valve into it.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The brake booster might work since it isn't a flowing port. Charges the booster and the flow stops until a brake apply is made. Using one of the vacuum ports going to a single cylinder (usually #4) works just as well. Maybe even better with pulses in the runner maybe making a stronger vacuum signal.

That front port, no-no for a flowing vacuum port (PCV, canister purge, etc.)
Vacuum signals shouldn't be an issue. But still I would not hook anything to it if possible, just to prevent false MAP signals.

On speed density EFI the MAP signal is probably the most important signal there is. Knowing what the air pressure is going into the manifold dictates the air flow into the cylinder and thus the fuel needs. OK, maybe the second most needed sensor since the Oxygen sensor is needed to get even a basic tune on these self tuning EFI kits.
 

badandy73

Contributor
Broncoholic
Joined
Jul 18, 2007
Messages
219
Following this thread as I'm fighting an oil leak coming from the breather on a set of bronco script valve covers on a new blueprint 306. Figured it was a mfg defect/ bad cover, so blueprint sent me a replacement set. Swapped the new one on (driver's side only) and leak got a lot worse. Pulled it off and inspected the baffle in comparison to the first- original looked to have better coverage, so pinched it shut even more to narrow down the baffle 'window' and also made sure the tabs were laying as flat as possible against the base of the breather tube and put it back together. Didn't make a difference and now back to square one with the original leak.

Passenger side is plumbed with a functioning PCV valve running to the base of the sniper. Blueprint's tech had me verify that it was working correctly and also had me check the breather tube while holding a paper towel over it, wasn't puffing or blowing out excessively. After those checked out, he assures me it isn't excessive blow-by or some other issue with the motor.

One thought is to go to another brand/ style of valve covers with a different style breather setup (or solid oil fill cap as 68ford mentioned). Anyone running something like this with good results?:

summitracing.com/parts/pro-302-135/make/ford

Wanted to follow up on this thread after success drying up my breather leak. Installed the valve covers mentioned above #302-135 with the matching breather #302-435 along with a set of fel-pro perma-dry (blue rubber) gaskets #VS13264T and they're still dry as a bone a month and almost a thousand miles later.

Hopefully this saves somebody a headache dealing with the leaking scott drake covers. Baffle design is terrible on the breather side, pro-form's are much better and stand the breather up vertical, how it should be.
 
Top