BRONCITIS74
Full Member
- Joined
- Oct 4, 2015
- Messages
- 340
Wow. A lot of information. I will start checking all these things. Thanks, guys,
Mike
Mike
Maybe yours was a high-quality original. Many other stories of quick failures when thermal compound was not used.No, that's not likely the cause since I've driven on an ICM not mounted to any heat sink.
I thought, at least as far as the Mustangs were concerned, all 86 to 93 EFI 5.0 engines were mass air.For it to be a MAF engine, it must be '94-96, which also makes it CCD.
86 - 88 mustangs were speed density.Maybe yours was a high-quality original. Many other stories of quick failures when thermal compound was not used.
Maybe simply the difference between quality, OE parts, and cheap imported aftermarket parts. Or just bad luck with the others…
I thought, at least as far as the Mustangs were concerned, all 86 to 93 EFI 5.0 engines were mass air.
Ford continued to use speed density on other vehicles, but I thought the Mustangs always had the MAF. Is that not the case?
Sorry I didn’t read the text in this case like I usually do.
‘88 California cars were MAF86 - 88 mustangs were speed density.
Didn't Ford go to remote TFI in the SN95 stuff? I know that 96 E350 vans were remote. I'm running a van harness modified to SN95 EFI and have remote TFI.
I mention this as I recall reading about how to wire up a remote TFI for the 89-93 mustangs.
Tim
Yeah I guess we need him to post a pic of the distributorDidn't Ford go to remote TFI in the SN95 stuff? I know that 96 E350 vans were remote. I'm running a van harness modified to SN95 EFI and have remote TFI.
I mention this as I recall reading about how to wire up a remote TFI for the 89-93 mustangs.
Tim
Can you post pics of the engine so we can determine what year the EFI system is? 94-95 are a slightly different system. Also, your coolant temps are too low for a factory EFI setup. Newer vehicles run hotter than old carbureted rigs. Most of us with EFI use a 195* thermostat with a good radiator and fan/shroud setup.I have a 74 Bronco that has been converted to a 5.0 efi motor. I think the motor is from '93 or '94. It has a single stock rear gas tank. The fuel line , the fuel pump (in line, mounted on the frame) and the fuel filter have all been replaced. The rotor and spark plug wires are only 2 years old. The truck runs fine till the outside temp gets into the 90's. Then, every once in a while, the motor stutters, then kills. If I let it sit for a few minutes, it starts and runs fairly good. I talked to a guy at the Wisconsin Super Celebration and he told me he had the same problem. I took his advice and replaced the stock radiator with a 4-core radiator and added a 6 blade fan, and added a new shroud. It runs at about 165 deg on the hiway, but gets to 180 in town. That still isn't that hot, but it still kills. Have any of you guys had the problem or know how to remedy it? Any help would really be appreciated. Thanks.
Yes they did. The SN95 also went to computer controlled dwell where the trucks stayed with TFI controlled dwell long after they went to remote TFI. I don't remember if the last year or two were still TFI controlled dwell. The factory color coding was black for computer controlled dwell and gray for TFI controlled dwell. Learned a bunch of this stuff when playing with a stroked in a Ranger. The remote distributor is also shorter, to the point it can interfere with Explorer fuel rails. Mix and match parts. Remote TFI and pickup inside of an integral TFI distributor housing.Didn't Ford go to remote TFI in the SN95 stuff? I know that 96 E350 vans were remote. I'm running a van harness modified to SN95 EFI and have remote TFI.
I mention this as I recall reading about how to wire up a remote TFI for the 89-93 mustangs.
Tim
I must have missed where he mentioned the engine being from a Mustang. I always have truck engines on the brain, so that's what my comment presumes. If he's using Mustang wiring, he should ignore my previous post....as far as the Mustangs were concerned...
Sorry I didn’t read the text in this case like I usually do.
The truck runs fine till the outside temp gets into the 90's. Then, every once in a while, the motor stutters, then kills. If I let it sit for a few minutes, it starts and runs fairly good.
We use a lot of both dielectric grease and thermal transfer paste in our marine electronics products and, yep, the consistencies and colors are quite different. ;-)Y
Usually when you bought a new TFI or distributor there was a little capsule of the heat transfer grease. I've always found it to be a very different consistency than the dielectric grease used to keep the spark plug boots from sticking to the spark plugs.






