• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Took over 40 hours of work in total to replace my suspension, most steering components, bushings, and power steering box (first time for me doing any of that).

Doesn’t look much different from the outside, but it rides amazing! Used to be like a brick over any little bump with the accompanying clunks, rattles, and squeaks. Now it’s smooth as silk!

It’s tracking very straight, but I am going to take it for an alignment just to make sure / dial it in.

IMG_3832.jpeg
 

Vincen

Contributor
Sr. Member
Joined
Nov 24, 2012
Messages
369
Took over 40 hours of work in total to replace my suspension, most steering components, bushings, and power steering box (first time for me doing any of that).

Doesn’t look much different from the outside, but it rides amazing! Used to be like a brick over any little bump with the accompanying clunks, rattles, and squeaks. Now it’s smooth as silk!

It’s tracking very straight, but I am going to take it for an alignment just to make sure / dial it in.

View attachment 944540
What suspension system did you go with?
 

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
What suspension system did you go with?
Wild Horses stock height kit, new tie rod and drag link assembly, overkill heavy duty shackles, spring cups, all new hardware, new bump stops, etc.

My fenders are cut aggressively (by PO), and I wanted to keep the center of gravity low. I think the stance looks good and I think the back will settle a bit as well.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
So in Moab a couple weeks ago I noticed while airing down that the valve stem on my beadlock was cracked. Wow, I'd never noticed and I mounted the new tires last summer after 6 yrs with the old tires.

I moved around to another tire and SAME! Dang!

Next one- crapola!!

Sure enough, # 4 also. I mean two of them were so cracked so bad I was worried about airing up and airing down so I was extra gentle. Well, finally got around to doing them today since next week I am not sure if I'm driving all 250 miles or trailering part of the way at 70 mph but I'm glad I rememberd to change them out tonight.

Got each one done in under 45 min as I'm in no hurry to overtighten or not torque the 32 bolts down in sequence properly...

Glad I remembered! :)

Change your valve stems. Mine were 7 yrs old and all 4 were cracked bad. 2 were cracked really bad. I'd just mounted these tires last summer and I don't know why I didn't replace them then but I didn't and should have even tho they looked perfect 10 mo ago.

The pic I have of the stem was the best stem. I'll update with one of the other almost torn thru stems later.
 

Attachments

  • 20250517_193950.jpg
    20250517_193950.jpg
    329.5 KB · Views: 88
  • 20250517_172018.jpg
    20250517_172018.jpg
    213.5 KB · Views: 87
  • 20250517_173340.jpg
    20250517_173340.jpg
    292.9 KB · Views: 74
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Do you think it’s due to the quality of the materials going downhill over the years? Or have valve stems always deteriorated like this for you?
Maybe because they get hit a lot on the trails, but I never had cracking valve stems in 50 years of running rubber stems.
Of course, most of those were on passenger cars, and my last two sets (Bronco and pickup) were metal, and maybe that hid the cracks better underneath.
Guessing you couldn’t use metal in your application, but I had wheels with a fairly protected stem pockets and didn’t use them as hard as you do.
 

serial car restorer

Yes, I'll restore almost anything...
Joined
Aug 27, 2024
Messages
742
Loc.
Western Oregon
I don't think the quality has changed much over the years. I haven't worked in the ire industry since 1998. But my recollection from back then is that cracked stems after 6-7 years wouldn't surprise me at all. There's a reason that most tire shops routinely change rubber stems whenever new tires are installed.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Do you think it’s due to the quality of the materials going downhill over the years? Or have valve stems always deteriorated like this for you?
Maybe because they get hit a lot on the trails, but I never had cracking valve stems in 50 years of running rubber stems.
Of course, most of those were on passenger cars, and my last two sets (Bronco and pickup) were metal, and maybe that hid the cracks better underneath.
Guessing you couldn’t use metal in your application, but I had wheels with a fairly protected stem pockets and didn’t use them as hard as you do.
I've never had stems crack before and just as old... I really think it's quality like everything else seems to be suffering from the past 20 yrs with advances in tech and the push that profits must be made which is the driver behind manufacturing today.

My reasoning is this- look at almost everything else. From washing machines, to auto parts to most everything else. Why not make a product the consumer has to purchase more often instead of Grandpa's freezer lasting 40 yrs or your mom's Maytag lasting for 40 plus years. Those days are gone forever and I think valve stems easily lasting 8-10 yrs are over.

That's my thought because why wouldn't the company that makes several products not want to make the same profits on their tire stem products as they do with their other product lines when all they have to do is make them last 10-20 percent less.
 

hsach

Contributor
Members Only
Joined
Apr 19, 2013
Messages
435
Still doing some last minute fixes before it goes to paint in June. Got one of the doors back from sand blasting, and had to finish cleaning the inside. So tight in there, he couldn't get to everything I wanted. It was just surface rust, so I sanded it by hand as much as I could and then hit it with a rust converter. After that dried fully, I painted some Rust Bullet on the inside bottom, inside front by the hinges, and the inside area back where the door latch attaches. Basically anywhere it had surface rust previously. A lot of work, but it looks great inside the doors now. Here are a couple of pics to show the rust inside, and how it looks after sanding and applying the rust converter.
20250504_113533.jpg

20250518_095813.jpg
 

Meddle

Contributor
Jr. Member
Joined
Dec 22, 2023
Messages
129
Loc.
Upstate NY
Installed the windshield stiffeners from BCB. Wanted them as high as possible for head space so I used a coupling nut as a riser. Just cleared the wiper cover and leaves plenty of room for the visors to fold up. I wasn’t sure if I was going to like the look but I actually do, especially the Fourtrecks kit on the roll cage. And it definitely stiffens things up. Hopefully this will fix my issue with the rampage soft top pulling my windshield and door back when tightened down.

IMG_1433.jpeg IMG_1435.jpeg
IMG_1436.jpeg IMG_1434.jpeg
 
Top