• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Began the wiring process. Started on the dash with the Painless kit. Went with this because I wanted stock connectors, labeled wires and more accessory outlets.
c92eae3bf2f30f0dc444c731d59228bf.jpg

627a9d2138941ac997d9fdd92ee96e3c.jpg

f98f780f59c764ae5ef69a08eac433d9.jpg

6cf1556c68382e910fdecce443434f45.jpg

Kyle


Sent from my iPhone using Tapatalk
Might I throw in a spot of wisdom. When I did my dash, I also had it out on a table, I went to great lengths to wire, tab, wrap everything together.

Don't. An issue I am having is the bundle of wires which looks so very nice wrapped in protective covering, and taped at interval, is now so tight it can wiggle connections off the back of the radio, and dash lights. Working on that. I would only use wrap going through firewall or where you need wire protected like frame or engine bay.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
We all hope & pray when slowly "cracking" each wtrpump bolt that we don't hear that dreaded metallic snap... or feel the wrench go from 20ftlbs of torque to ZERO in a split second! Aaaaugh!! lol
I've found with more success than failure, break free, heat, and actually tighten the rusty bolt a little, then remove it.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Draining rad fluid for new fresh 50/50 premix prestone.
Installed EVAP canister covers, the pesky little round ones. Both. I'm using large evap hole as line to tank, small one as line to the aircleaner assembly behind the aircleaner so there is a little vacuum purging the evap/fuel tank.

Probably going to have to remove thermostat as the darn block is just not draining enough overnight, dang it.

Reseting idle speed up from 450 to 650. Leaning mixture 1/8th of a turn on my quadrajet adjustable mixture carb.

Drill milodon 7qt dual sump oil pan drain plug to accept stewart temp probe.

Maybe time for ream attempt on knuckle tie rod hole
 

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Might I throw in a spot of wisdom. When I did my dash, I also had it out on a table, I went to great lengths to wire, tab, wrap everything together.

Don't. An issue I am having is the bundle of wires which looks so very nice wrapped in protective covering, and taped at interval, is now so tight it can wiggle connections off the back of the radio, and dash lights. Working on that. I would only use wrap going through firewall or where you need wire protected like frame or engine bay.
I agree. I'm leaving most of the wiring un loomed. However it is bundle tighly with ties. I also leave some slack on each connection to switches and terminals.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Went to the local Cars and Coffee Sunday, guy pulls up next to me and Clifford in a restored 67 that was originally sold in the Netherlands. Shares the interesting life story of the Bronco on how a Canadian purchased it, restored it, and then he bought it.

First speedo I have seen in Kilometers!
 

Attachments

  • 20260719_081923[1].jpg
    20260719_081923[1].jpg
    163.9 KB · Views: 108

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Went to run an errand and turned the key. It cranked for a moment, and I remembered I didn't set the choke, so I cranked it again and it just clicked. The battery is in good shape, so I checked the starter connection and that was tight too. Later on, I tried it again and it started right up. Grrr... I hate these intermittent issues.
 

BronCowie

Contributor
Old Timer
Joined
Apr 24, 2007
Messages
8,291
Loc.
Vancouver, WA
Went to run an errand and turned the key. It cranked for a moment, and I remembered I didn't set the choke, so I cranked it again and it just clicked. The battery is in good shape, so I checked the starter connection and that was tight too. Later on, I tried it again and it started right up. Grrr... I hate these intermittent issues.

Did you check for a good "clean" ground connection(s)? :unsure:
 

kman67

Contributor
Full Member
Joined
Apr 8, 2005
Messages
180
Loc.
Aptos
Might I throw in a spot of wisdom. When I did my dash, I also had it out on a table, I went to great lengths to wire, tab, wrap everything together.

Don't. An issue I am having is the bundle of wires which looks so very nice wrapped in protective covering, and taped at interval, is now so tight it can wiggle connections off the back of the radio, and dash lights. Working on that. I would only use wrap going through firewall or where you need wire protected like frame or engine bay.

Thanks 73azbronco and gnsteam for the advise. I haven’t loomed or taped any of the dash wires but, I’ll zip tie them together. My daughters helped me get the dash in the Bronco so I can get more wires run through out the rest of the rig.
351eadd103ab1c031e8910ca212e7a17.jpg

a19e8cb65dc96671f522336fb408eb58.jpg

Kyle


Sent from my iPhone using Tapatalk
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Just installed my grill letters and used the template that Tosh had provided in this thread. From the time I printed the template, till I finished installing the letters took about an hour. Super easy this way.
I need to do this. Where did you find the template?
 
Top