• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

FordBronc

Contributor
Bronco's, yea I have a couple.
Joined
Dec 26, 2010
Messages
1,518
Loc.
Polk County, Missouri
Put front and rear on top of some SOLID 35" tall stands, got the front suspension to full droop and started working on getting that front axle rmvd. It is a 75/76 (?) F250 low pinion POS that the PO cobbed under there. Do not even ask about the grill. I have a patch panel for it.
PXL_20261109_235946674.jpg

PXL_20261110_000029980.jpg

PXL_20261109_232637412.jpg

PXL_20261110_000014767.jpg
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
Well it was only rolled once or twice haha, plus it's originally from NE so it's a little rotten. All the connections seemed great, only broke the retaining tabs on one plug yesterday and it's easily fixed. I'm sure a full rewire is in its future, but I want to get this one on the road. The goal is to drive it to Christmas dinner. The tub I've been working on in my garage is from the high mtn desert and only needed floors. Rockers and pillars are solid. Things got out of hand with my 69 with the 3 link and LS so this one's supposed to be cheap and simple.
My advice is to inspect and repair any damage while the harness is out...but I would never install a "new" harness in an EB.

The factory harness is vastly superior to any harness made today. It fits, it works, it has the correct connectors, and it is has been perfectly adequate for 50 years. Far too many people want to start adding accessories and additional features, and splice in a bunch of garbage that has no business attached to the factory harness. And then you get spaghetti. Do yourself a favor, and stay the course. Commit to your existing harness, and when the day comes that you want to add an accessory...do it the modern way. Do NOT think of installing a new harness with additional circuits. Bite the bullet, and order up an SPOD or build your own stand alone switch and relay panel. If you install a high amp alternator, tie it to the battery, install a digital volt meter, and leave your ammeter circuit alone. Same thing with custom audio. Add it as a stand alone harness, and feed it from your battery direct, with a fuse and relay.

I have never met a single Bronco owner that ever said: "I'm SO glad that the previous owner spliced in all these wires, cooked the factory harness, chopped off all these ends, and added all this crap and stuffed it back under the dash!"
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
My advice is to inspect and repair any damage while the harness is out...but I would never install a "new" harness in an EB.

The factory harness is vastly superior to any harness made today. It fits, it works, it has the correct connectors, and it is has been perfectly adequate for 50 years. Far too many people want to start adding accessories and additional features, and splice in a bunch of garbage that has no business attached to the factory harness. And then you get spaghetti. Do yourself a favor, and stay the course. Commit to your existing harness, and when the day comes that you want to add an accessory...do it the modern way. Do NOT think of installing a new harness with additional circuits. Bite the bullet, and order up an SPOD or build your own stand alone switch and relay panel. If you install a high amp alternator, tie it to the battery, install a digital volt meter, and leave your ammeter circuit alone. Same thing with custom audio. Add it as a stand alone harness, and feed it from your battery direct, with a fuse and relay.

I have never met a single Bronco owner that ever said: "I'm SO glad that the previous owner spliced in all these wires, cooked the factory harness, chopped off all these ends, and added all this crap and stuffed it back under the dash!"
Sorry, I have to ask. What's the beef with new harnesses? I was very happy with the Centech. I did re-engineer a couple things I wanted on relays though.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
Sorry, I have to ask. What's the beef with new harnesses? I was very happy with the Centech. I did re-engineer a couple things I wanted on relays though.
The Bronco wiring harness was unique for every single year of production. The obvious change was between 70 and 71 when the fuse box moved. But every single year is different. There is only ONE Centech harness. So if you have a 66-70, you have to move the fuse box. Centech does not plug and play with Duraspark, and Centech uses funky connectors on the wipers, turn signal, etc. I don't recall if centech has the molded connectors for the marker lights, but it doesn't matter...because Centech is no longer available. If you have a 71-72 with the voltage regulator near the battery...and you don't mind splicing your wiper connector, ignition switch, and turn signal plug...you are in good shape. Bear in mind that there is no such thing as "good" vs "bad." There is only "better" and that is comparing "what you have" and "what you can get."

When I install a harness, I want the molded plugs to fit the devices. I want the factory switches to plug in an work. I want the firewall grommet to fit the hole. And I want the resistor wire to be in the harness. (sometimes) But credit where credit is due...compared to a junk factory harness, the Centech is GREAT. and their soldered pc board fuse arrangement is superior to the factory one. But compared to a properly preserved factory harness, I'm going factory every time. Now compared to a fully refurbished, re-taped and tested used harness from the NorthEast...well...doesn't matter, because I bought the last one.

When you figure a new painless harness is about $1000, and a factory harness with some carefully soldered and shrunk terminals is FREE...the decision is easier.

Keep in mind that I once bought a whole junk 1970 Ford Bronco from a wrecker just to get the harness. Only to learn that it wouldn't actually fit in my 71. (Turns out it was the best $500 I ever invested after Bronco's went crazy...)
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
The Bronco wiring harness was unique for every single year of production. The obvious change was between 70 and 71 when the fuse box moved. But every single year is different. There is only ONE Centech harness. So if you have a 66-70, you have to move the fuse box. Centech does not plug and play with Duraspark, and Centech uses funky connectors on the wipers, turn signal, etc. I don't recall if centech has the molded connectors for the marker lights, but it doesn't matter...because Centech is no longer available. If you have a 71-72 with the voltage regulator near the battery...and you don't mind splicing your wiper connector, ignition switch, and turn signal plug...you are in good shape. Bear in mind that there is no such thing as "good" vs "bad." There is only "better" and that is comparing "what you have" and "what you can get."

When I install a harness, I want the molded plugs to fit the devices. I want the factory switches to plug in an work. I want the firewall grommet to fit the hole. And I want the resistor wire to be in the harness. (sometimes) But credit where credit is due...compared to a junk factory harness, the Centech is GREAT. and their soldered pc board fuse arrangement is superior to the factory one. But compared to a properly preserved factory harness, I'm going factory every time. Now compared to a fully refurbished, re-taped and tested used harness from the NorthEast...well...doesn't matter, because I bought the last one.

When you figure a new painless harness is about $1000, and a factory harness with some carefully soldered and shrunk terminals is FREE...the decision is easier.

Keep in mind that I once bought a whole junk 1970 Ford Bronco from a wrecker just to get the harness. Only to learn that it wouldn't actually fit in my 71. (Turns out it was the best $500 I ever invested after Bronco's went crazy...)
Thanks for the explanation!

Nothing would have been drop-in for me. I had lots of custom stuff. As well as not much of an original harness left to work with.
- Headlight relays
- Heater fan relays
- Ignition system and EFI relay
- Fitech EFI
- Delay wiper switch (just needs the extra ground wire)
- Duraspark and an E-coil (no resistor). If the Duraspark ever quits, I have a GM module spare on a CPU heat sink in the glove box I can plug in.
- 3G alternator (kept ammeter for loads only, I have voltage on the handheld)
- '86 tilt column and used the column hazard and ignition switches and the turn signal and horn
- 130w KC Daylighters on the bumper
- LED strip "dome light" mounted on the windshield frame
- Dimming rear view mirror with lights, temperature and compass
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I tend to wire as James suggests. The original harness is left alone as much as possible. I do pull key-on, accessory only, and similar signals from it, but the circuits that those signals drive are in stand-alone harnesses.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
Thanks for the explanation!

Nothing would have been drop-in for me. I had lots of custom stuff. As well as not much of an original harness left to work with.
- Headlight relays
- Heater fan relays
- Ignition system and EFI relay
- Fitech EFI
- Delay wiper switch (just needs the extra ground wire)
- Duraspark and an E-coil (no resistor). If the Duraspark ever quits, I have a GM module spare on a CPU heat sink in the glove box I can plug in.
- 3G alternator (kept ammeter for loads only, I have voltage on the handheld)
- '86 tilt column and used the column hazard and ignition switches and the turn signal and horn
- 130w KC Daylighters on the bumper
- LED strip "dome light" mounted on the windshield frame
- Dimming rear view mirror with lights, temperature and compass
Here’s my dash. My arbs are on a separate harness, as is eec4 power.
 

Attachments

  • IMG_2106.jpeg
    IMG_2106.jpeg
    180.4 KB · Views: 78

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I used something like these for the ARB's in the 4rnnr: Clippard 3-Way Toggle No more sometimes problematic ARB solenoid valves.
Converted them to 4mm tubing & fittings so no more nearly proprietary ARB 5mm tubing and fittings. Ran the valve exhausts together and then out to the engine bay and put a sintered muffler/filter on the end to keep junk out and allow the tiny bit of gear lube that makes it's way into the tubing to not drain on the carpet. :)
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
I used something like these for the ARB's in the 4rnnr: Clippard 3-Way Toggle No more sometimes problematic ARB solenoid valves.
Converted them to 4mm tubing & fittings so no more nearly proprietary ARB 5mm tubing and fittings. Ran the valve exhausts together and then out to the engine bay and put a sintered muffler/filter on the end to keep junk out and allow the tiny bit of gear lube that makes it's way into the tubing to not drain on the carpet. :)
I applaud the effort, and I think it's a definite upgrade. But as with many upgrades, the question is always where to stop. I also deleted the ARB solenoid valves on the last Bronco before this Bronco. But instead of a Clippard valve, I used a Fuller range valve mounted to the shifter for the front ARB and a Bendix TW-1 select valve and an "axle diff lock-unlock" plate mounted in the fuel tank select hole for the rear.

People that know me understand that I have a simple design constraint for any car that I own. The design MUST include tactile feedback, and must be intuitive enough to be used by an operator that is distracted, can't see, won't look, or otherwise impaired. So every control must be easily reached, easily manipulated, and not misunderstood. I have found that when I want to select the front ARB, I am usually VERY busy, concentrating on my spotter, or my line, it is often dark, and noisy, and the need to control the front locker is immediate. So I have found that placing the selector switch on the shift stick is very convenient.

On my Rubihara, I just put a toggle switch on the dash, and tried my first Eaton 4 pinion magnetic e-locker. Dana Spicer just bought Eaton, so that means Detroit, Tru-trac, Dyneer, are all going to Dana. Nothing good has ever come from being bought by Dana.

As a rule, I will not own a car that I cannot operate. I once rented a brand new Subaru in Orlando, and had to pull over numerous times in order to figure out the defroster. I also rented a Hyundai Palisade in Ireland, and the radio volume knob became the heater control knob at random. There are rental cars that I have elected to have towed back because I could not figure out how to open the fuel door. And yes, I do own a Tesla, and no it cannot be driven without taking your eyes off the road, and diverting your full attention to the touchscreen. Unlike the Chevy Volt, which is impossible to select a comfortable heater position even when stationary...the Tesla heater can be adjusted. But it requires your undivided attention. Most people hate Tesla drivers, and this is one more reason why. So my rule is that if I can't jump in the car, and GO within 30 seconds, and every control must be intuitive enough that it can be adjusted while underway. In the dark, in the rain, without opening an internet browser to ask AI how to use it.

Here's my 69 Bronco with the front ARB selector over-ride on the shifter. I went back to ARB solenoids, because I had extras. I can find it in the dark, no eyes, no drama.
 

Attachments

  • IMG_5450.jpeg
    IMG_5450.jpeg
    226.1 KB · Views: 51

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
My experience has been that ARB's do not lock and unlock instantly and the use of the truck was extremely unlikely to require it, so I planned accordingly. There were no other toggles around those two, so as long as the driver kept "Left = Front, Right = Rear" in mind they could be reached and operated blindly from the normal driving position. No third pedal in that vehicle, so there's that.
Wagon got Tru-Tracs mostly to eliminate the confused driver issue entirely. It's use shouldn't ever need more than that.

There's good reason why I call the FSB "Snowball" and it has little to do with it being white.

oh yeah, Subaru's driving assist nannies! Oey! Since it didn't like my line going up PCH in Malibu I let it steer. Can you say constructive interference? It would have wrecked the car if left alone. Too much pain to turn all of it off, easier to just not drive it. She who does drive it likes it enough but won't be buying another one.

And.... on topic, nothing today or this week. Next weekend will hopefully be different. The Bronc-up is going to come out of hibernation and get cleaned out, all of its parts gathered up and put in one place. That eventually won't be my backyard.
 

FordBronc

Contributor
Bronco's, yea I have a couple.
Joined
Dec 26, 2010
Messages
1,518
Loc.
Polk County, Missouri
Coil springs removed, bottom spring cups removed. Lots of PB Blaster on the radius arm hdwr. Need to remove the passenger side knuckle to move it to the replacement axle. Might get to that and the radius arms tomorrow.
ax.jpg
 
Top