@1969miller found a home for his body quick! Ha haAdded another bronco to the fleet.
@1969miller found a home for his body quick! Ha haAdded another bronco to the fleet.
Haha if Cole wants another one he's welcome to it!@1969miller found a home for his body quick! Ha ha
My advice is to inspect and repair any damage while the harness is out...but I would never install a "new" harness in an EB.Well it was only rolled once or twice haha, plus it's originally from NE so it's a little rotten. All the connections seemed great, only broke the retaining tabs on one plug yesterday and it's easily fixed. I'm sure a full rewire is in its future, but I want to get this one on the road. The goal is to drive it to Christmas dinner. The tub I've been working on in my garage is from the high mtn desert and only needed floors. Rockers and pillars are solid. Things got out of hand with my 69 with the 3 link and LS so this one's supposed to be cheap and simple.
Sorry, I have to ask. What's the beef with new harnesses? I was very happy with the Centech. I did re-engineer a couple things I wanted on relays though.My advice is to inspect and repair any damage while the harness is out...but I would never install a "new" harness in an EB.
The factory harness is vastly superior to any harness made today. It fits, it works, it has the correct connectors, and it is has been perfectly adequate for 50 years. Far too many people want to start adding accessories and additional features, and splice in a bunch of garbage that has no business attached to the factory harness. And then you get spaghetti. Do yourself a favor, and stay the course. Commit to your existing harness, and when the day comes that you want to add an accessory...do it the modern way. Do NOT think of installing a new harness with additional circuits. Bite the bullet, and order up an SPOD or build your own stand alone switch and relay panel. If you install a high amp alternator, tie it to the battery, install a digital volt meter, and leave your ammeter circuit alone. Same thing with custom audio. Add it as a stand alone harness, and feed it from your battery direct, with a fuse and relay.
I have never met a single Bronco owner that ever said: "I'm SO glad that the previous owner spliced in all these wires, cooked the factory harness, chopped off all these ends, and added all this crap and stuffed it back under the dash!"
The Bronco wiring harness was unique for every single year of production. The obvious change was between 70 and 71 when the fuse box moved. But every single year is different. There is only ONE Centech harness. So if you have a 66-70, you have to move the fuse box. Centech does not plug and play with Duraspark, and Centech uses funky connectors on the wipers, turn signal, etc. I don't recall if centech has the molded connectors for the marker lights, but it doesn't matter...because Centech is no longer available. If you have a 71-72 with the voltage regulator near the battery...and you don't mind splicing your wiper connector, ignition switch, and turn signal plug...you are in good shape. Bear in mind that there is no such thing as "good" vs "bad." There is only "better" and that is comparing "what you have" and "what you can get."Sorry, I have to ask. What's the beef with new harnesses? I was very happy with the Centech. I did re-engineer a couple things I wanted on relays though.
When is a heated steering wheel in your future?The days are getting shorter...and darker! still drive to work everyday, not bad for a 53 year old!
Thanks for the explanation!The Bronco wiring harness was unique for every single year of production. The obvious change was between 70 and 71 when the fuse box moved. But every single year is different. There is only ONE Centech harness. So if you have a 66-70, you have to move the fuse box. Centech does not plug and play with Duraspark, and Centech uses funky connectors on the wipers, turn signal, etc. I don't recall if centech has the molded connectors for the marker lights, but it doesn't matter...because Centech is no longer available. If you have a 71-72 with the voltage regulator near the battery...and you don't mind splicing your wiper connector, ignition switch, and turn signal plug...you are in good shape. Bear in mind that there is no such thing as "good" vs "bad." There is only "better" and that is comparing "what you have" and "what you can get."
When I install a harness, I want the molded plugs to fit the devices. I want the factory switches to plug in an work. I want the firewall grommet to fit the hole. And I want the resistor wire to be in the harness. (sometimes) But credit where credit is due...compared to a junk factory harness, the Centech is GREAT. and their soldered pc board fuse arrangement is superior to the factory one. But compared to a properly preserved factory harness, I'm going factory every time. Now compared to a fully refurbished, re-taped and tested used harness from the NorthEast...well...doesn't matter, because I bought the last one.
When you figure a new painless harness is about $1000, and a factory harness with some carefully soldered and shrunk terminals is FREE...the decision is easier.
Keep in mind that I once bought a whole junk 1970 Ford Bronco from a wrecker just to get the harness. Only to learn that it wouldn't actually fit in my 71. (Turns out it was the best $500 I ever invested after Bronco's went crazy...)
Here’s my dash. My arbs are on a separate harness, as is eec4 power.Thanks for the explanation!
Nothing would have been drop-in for me. I had lots of custom stuff. As well as not much of an original harness left to work with.
- Headlight relays
- Heater fan relays
- Ignition system and EFI relay
- Fitech EFI
- Delay wiper switch (just needs the extra ground wire)
- Duraspark and an E-coil (no resistor). If the Duraspark ever quits, I have a GM module spare on a CPU heat sink in the glove box I can plug in.
- 3G alternator (kept ammeter for loads only, I have voltage on the handheld)
- '86 tilt column and used the column hazard and ignition switches and the turn signal and horn
- 130w KC Daylighters on the bumper
- LED strip "dome light" mounted on the windshield frame
- Dimming rear view mirror with lights, temperature and compass
^^^ Damn that looks good. My dash and dash pad are far from that clean.Here’s my dash. My arbs are on a separate harness, as is eec4 power.
I applaud the effort, and I think it's a definite upgrade. But as with many upgrades, the question is always where to stop. I also deleted the ARB solenoid valves on the last Bronco before this Bronco. But instead of a Clippard valve, I used a Fuller range valve mounted to the shifter for the front ARB and a Bendix TW-1 select valve and an "axle diff lock-unlock" plate mounted in the fuel tank select hole for the rear.I used something like these for the ARB's in the 4rnnr: Clippard 3-Way Toggle No more sometimes problematic ARB solenoid valves.
Converted them to 4mm tubing & fittings so no more nearly proprietary ARB 5mm tubing and fittings. Ran the valve exhausts together and then out to the engine bay and put a sintered muffler/filter on the end to keep junk out and allow the tiny bit of gear lube that makes it's way into the tubing to not drain on the carpet.![]()






