• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

FordBronc

Contributor
Bronco's, yea I have a couple.
Joined
Dec 26, 2010
Messages
1,518
Loc.
Polk County, Missouri
Put front and rear on top of some SOLID 35" tall stands, got the front suspension to full droop and started working on getting that front axle rmvd. It is a 75/76 (?) F250 low pinion POS that the PO cobbed under there. Do not even ask about the grill. I have a patch panel for it.
PXL_20261109_235946674.jpg

PXL_20261110_000029980.jpg

PXL_20261109_232637412.jpg

PXL_20261110_000014767.jpg
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
My advice is to inspect and repair any damage while the harness is out...but I would never install a "new" harness in an EB.

The factory harness is vastly superior to any harness made today. It fits, it works, it has the correct connectors, and it is has been perfectly adequate for 50 years. Far too many people want to start adding accessories and additional features, and splice in a bunch of garbage that has no business attached to the factory harness. And then you get spaghetti. Do yourself a favor, and stay the course. Commit to your existing harness, and when the day comes that you want to add an accessory...do it the modern way. Do NOT think of installing a new harness with additional circuits. Bite the bullet, and order up an SPOD or build your own stand alone switch and relay panel. If you install a high amp alternator, tie it to the battery, install a digital volt meter, and leave your ammeter circuit alone. Same thing with custom audio. Add it as a stand alone harness, and feed it from your battery direct, with a fuse and relay.

I have never met a single Bronco owner that ever said: "I'm SO glad that the previous owner spliced in all these wires, cooked the factory harness, chopped off all these ends, and added all this crap and stuffed it back under the dash!"
Sorry, I have to ask. What's the beef with new harnesses? I was very happy with the Centech. I did re-engineer a couple things I wanted on relays though.
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
The Bronco wiring harness was unique for every single year of production. The obvious change was between 70 and 71 when the fuse box moved. But every single year is different. There is only ONE Centech harness. So if you have a 66-70, you have to move the fuse box. Centech does not plug and play with Duraspark, and Centech uses funky connectors on the wipers, turn signal, etc. I don't recall if centech has the molded connectors for the marker lights, but it doesn't matter...because Centech is no longer available. If you have a 71-72 with the voltage regulator near the battery...and you don't mind splicing your wiper connector, ignition switch, and turn signal plug...you are in good shape. Bear in mind that there is no such thing as "good" vs "bad." There is only "better" and that is comparing "what you have" and "what you can get."

When I install a harness, I want the molded plugs to fit the devices. I want the factory switches to plug in an work. I want the firewall grommet to fit the hole. And I want the resistor wire to be in the harness. (sometimes) But credit where credit is due...compared to a junk factory harness, the Centech is GREAT. and their soldered pc board fuse arrangement is superior to the factory one. But compared to a properly preserved factory harness, I'm going factory every time. Now compared to a fully refurbished, re-taped and tested used harness from the NorthEast...well...doesn't matter, because I bought the last one.

When you figure a new painless harness is about $1000, and a factory harness with some carefully soldered and shrunk terminals is FREE...the decision is easier.

Keep in mind that I once bought a whole junk 1970 Ford Bronco from a wrecker just to get the harness. Only to learn that it wouldn't actually fit in my 71. (Turns out it was the best $500 I ever invested after Bronco's went crazy...)
Thanks for the explanation!

Nothing would have been drop-in for me. I had lots of custom stuff. As well as not much of an original harness left to work with.
- Headlight relays
- Heater fan relays
- Ignition system and EFI relay
- Fitech EFI
- Delay wiper switch (just needs the extra ground wire)
- Duraspark and an E-coil (no resistor). If the Duraspark ever quits, I have a GM module spare on a CPU heat sink in the glove box I can plug in.
- 3G alternator (kept ammeter for loads only, I have voltage on the handheld)
- '86 tilt column and used the column hazard and ignition switches and the turn signal and horn
- 130w KC Daylighters on the bumper
- LED strip "dome light" mounted on the windshield frame
- Dimming rear view mirror with lights, temperature and compass
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I tend to wire as James suggests. The original harness is left alone as much as possible. I do pull key-on, accessory only, and similar signals from it, but the circuits that those signals drive are in stand-alone harnesses.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I used something like these for the ARB's in the 4rnnr: Clippard 3-Way Toggle No more sometimes problematic ARB solenoid valves.
Converted them to 4mm tubing & fittings so no more nearly proprietary ARB 5mm tubing and fittings. Ran the valve exhausts together and then out to the engine bay and put a sintered muffler/filter on the end to keep junk out and allow the tiny bit of gear lube that makes it's way into the tubing to not drain on the carpet. :)
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
My experience has been that ARB's do not lock and unlock instantly and the use of the truck was extremely unlikely to require it, so I planned accordingly. There were no other toggles around those two, so as long as the driver kept "Left = Front, Right = Rear" in mind they could be reached and operated blindly from the normal driving position. No third pedal in that vehicle, so there's that.
Wagon got Tru-Tracs mostly to eliminate the confused driver issue entirely. It's use shouldn't ever need more than that.

There's good reason why I call the FSB "Snowball" and it has little to do with it being white.

oh yeah, Subaru's driving assist nannies! Oey! Since it didn't like my line going up PCH in Malibu I let it steer. Can you say constructive interference? It would have wrecked the car if left alone. Too much pain to turn all of it off, easier to just not drive it. She who does drive it likes it enough but won't be buying another one.

And.... on topic, nothing today or this week. Next weekend will hopefully be different. The Bronc-up is going to come out of hibernation and get cleaned out, all of its parts gathered up and put in one place. That eventually won't be my backyard.
 

FordBronc

Contributor
Bronco's, yea I have a couple.
Joined
Dec 26, 2010
Messages
1,518
Loc.
Polk County, Missouri
Coil springs removed, bottom spring cups removed. Lots of PB Blaster on the radius arm hdwr. Need to remove the passenger side knuckle to move it to the replacement axle. Might get to that and the radius arms tomorrow.
ax.jpg
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Picked up a 97 Explorer harness, ordered some replacement plugs that were damaged on it. Re-pinned the ECU plug for 96 Explorer EGR. (Thanks Garry)
Don't have anything to put it in yet, don't have a motor, and not sure what transmission to put behind it yet. (leaning towards a 5-spd) It will be ready for future duty ;)
 

Attachments

  • 20261113_102558[1].jpg
    20261113_102558[1].jpg
    230.1 KB · Views: 32

skrit

Contributor
Bull City Bronco
Joined
Apr 24, 2006
Messages
509
Loc.
Durham
Found a BC Broncos part I bought from a while ago hidden in a parts bin. Figured out what it was...a power steering filter. Modded a $6 Home Depot gate stop to mount it to my $30 Optima style battery tray and cheap Walmart Everstart Maxx Group 78 battery. Installed a Hayden fluid cooler on the front of the radiator for the PS and plumbed it up.
1000023371.jpg

1000023369.jpg

Just waiting on my 6AN adapter for the 4x4x2 high pressure port to finish the PS/HB plumbing.
1000023372.jpg

Next up..battery wiring. GM OEM style side mount battery cables, extended brass terminal bolts (so that I can attach jumper/trickle charge cables) and a power/ground distribution block.
 
Last edited:
Top