• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. J

    351 aluminum inatake install questions

    I just looked at several Stealth manifolds and all of them have 12 holes. My Edelbrock Performer has 12 too. So do all the after market intakes except the Offenhousers, that have 16. The earliest, as in the '69-'74 Ford 351 intakes, also have 16. I ran a '69 intake with later heads and plugged...
  2. J

    Clock

    https://www.redbubble.com/shop/bronco+clocks. A decent selection here too.
  3. J

    Any recommendations for a good place to send a set of injectors for cleaning and test

    Cleaning injectors is an easy DIY job. I have yet to have a reason to redo any of them.
  4. J

    1966 Drivers side footwell "flange" What is it?

    Was the angle bent piece mounted horizontally a '66 only item? There was nothing like it in my '68. Rust under the full width rubber floor mat was always a problem that I attempted to address by drilling holes at each end of the grooves. The holes plugged up and rust took over. All new sheet...
  5. J

    Cloth wire insulation replacement?

    The front harness including the engine compartment had no braid. After crawling under the truck I see the rear chassis harness has plenty of braid. I found a kit on CJ Pony Parts;https://www.cjponyparts.com/painless-performance-chassis-kit-classic-braid/p/WHC19/
  6. J

    Carb hangs up

    I have no problem with the solenoid. I have one on my '66 1.08 venturi 4100. I wire it with a rocker switch to increase RPMs on very bumpy roads to eliminate bump stall when the throttle is closed. My tune ie lower curb idle eliminated the dieseling after shut down. So it's not needed for the...
  7. J

    I've developed a timing issue...What am I missing here?

    I admit it was easier for me, because I have Sun distributor machine. There's not a lot of these around and mine is so old it has vacuum tubes, but it works. My high school automotive class in the mid '60s had one so I looked for many years to find one.
  8. J

    351W oil pan

    I still think it's a shame Ford or even someone else didn't make a stamping die based on the 289/302 '66-'77 Bronco oil pan, with a larger rear main bearing saddle and a deeper front sump to clear the 351 oil pump. With that the 351 engine swaps would be far easier and the pan wouldn't be hit by...
  9. J

    I've developed a timing issue...What am I missing here?

    A description of what Parkland Performance does to distributors or sells as a replacement would have helped. The OE distributor has only the vacuum and centrifugal advances to malfunction. Either of these are easy to repair or "curve". So you could have done whatever they did. Your chart of the...
  10. J

    Oil pan dipstick leak modification

    A '73 should have had a screw in dip stick tube.
  11. J

    Cloth wire insulation replacement?

    What wires were cloth covered on your '76? My '77 only had cloth insulation on the starter motor wire and then it was only near the wire clamps securing the wire. The rest of the wires and wire bundles had corrugated plastic looms.
  12. J

    351W oil pan

    It's not from a '69 Mustang. The only Mustang that had a 351 double sump pan was the '95 Cobra R. Those pans were designed for '79-'91 Crown Victoria police interceptors, where the vast majority were used. All the '69-'71 351W Mustangs had front sump pans. The duel sump 351W pans turned out to...
  13. J

    New to the forum

    I truly appreciate the tasteful look of the '68. Nothing over the top, while the few things an EB needs are there. Balance is novel where extremes are the norm.
  14. J

    Stock Air Cleaner Assembly, pictures, diagrams,and opinions...

    Have you ever considered posting in English? It would enhance your credibility.
  15. J

    What's a high-flow thermostat?

    Ford recommends 195 degree thermostats and the SpeedwayMotors Robertshaw is 180. I have a FlowCooler water pump that came with the recommendation of a RobertShaw thermostat so I got my high flow RobertShaw 195 degree from them.
  16. J

    Stock Air Cleaner Assembly, pictures, diagrams,and opinions...

    If enough EB owners interested in accurate reproduction parts demanded them, they would exist. If you own a Boss 429, you can find them, and those cars were produced in tiny numbers compared with any year EB. The problem is the vast majority of EB owners have no idea what a stock EB had as...
  17. J

    Carb hangs up

    I'm guessing that an extremely accurate restoration wasn't the goal when he bought a ChiCom 2150 carburetor with an automatic choke. The Bronco is a '68 when anti-dieseling solenoids didn't exist. The '68s had 2100s with manual chokes.
  18. J

    Carb hangs up

    When the engine is running, there is intake manifold vacuum pulling down on the throttle plates that could cause them to bind if there is rust or some other ruff surface on the bottom of the shaft or the bore it rotates in. The downward pressure from intake vacuum goes away with the engine shut...
  19. J

    77Â’ Bronco factory ignition wiring help

    An OE '77 ignition system is the best there is. If some knuckle head put a cheesy GM style HEI distributor in there, it's not an excuse to keep it. Replace the entire ignition system with OE Duraspark parts. The wire harness is FUBARed. A new firewall forward harness would be a good idea too...
  20. J

    Carb hangs up

    When an automatic choke is cold, the choke plate tries to partly or completely close before you touch the accelerator. When depressing the gas pedal, the choke plate closes and the fast idle cam moves. That holds the throttle partially open. This is just a part of the cold start procedure on...
Top