• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. trailpsycho

    Indy bound

    If you get some interest, let me know. I can probably make it out.
  2. trailpsycho

    Need you input on new build.

    Since I am running almost this exact setup, except that I have a 5.0, I will chime in on this. With the 351W, its an ideal setup...but you may need 4.88s. I had no problem pulling the mountains in CO...except for the climb out of Dillon back toward Denver. I had to come out of 5th into 4th...
  3. trailpsycho

    Yet another drivetrain problem

    You definitely want to keep the CV. Have it rebuilt or rebuild it yourself; the parts are available. You dont want it to fail; been there and done that...by the time it drops and hits the ground at speed...you have to replace it...and your lucky if you dont seriously damage something else...
  4. trailpsycho

    Set20 bearing removal

    My understanding is NO.
  5. trailpsycho

    Resto Sticker Shock

    Personally, I have never added up all the receipts from the multiple folders and binders. Unfortunately, my wife has to have the accounts rectified down to the penny. So with the help of Quicken, she knows whats been spent and likes to remind me fairly often. She claims its in the mid 30s. I...
  6. trailpsycho

    What to do

    CHeck this out. You can easily put the 5.0 intakes on your 5.8. http://www.bcbroncos.com/fuelefi.html There are sevearl people running this setup with good results...much cheaper than buying a 351 intake. Good luck!
  7. trailpsycho

    Resto Sticker Shock

    Ghost- I mean you no offense, but I thought these figures were old news. I always giggle (not is a sissy pansy way, but in a cynical-maniacal manner) when someone claims to have 'restored' a Bronco with only $10K into it including paint and such. "Yeah right, like polishing a turd". If you...
  8. trailpsycho

    scary experience!!

    The 9" should be 9 pints or 4.5 QTS, not 5 pints. The front end may be 5 pints, but the rear end is ~4.5 quarts. Dont venture too far until you get it filled up or you will be replacing your bearings again.
  9. trailpsycho

    Frame to cage tie in

    I have no bushings and its fine. No harsher ride and, so far, no other problems. It may be different depening on the condition of one's sheetmetal, and number of tie-in points. With only 2 or 4 there is probably much more flexing than with 6. I have 6...and I also have bars that run across...
  10. trailpsycho

    Power Steering Resevoir

    Man, why you gotta pick (on) my boogers! Its only meant to be functional. Obviously, I dont/couldnt weld for a living. I actually had some nice ones laid on the main can--outside, then when I got to the lid--it was a different guage and I had trouble with the boogs...didnt want to grind it...
  11. trailpsycho

    Kason/Emma Cruiser build thread WH 1" installed 3.18.15

    IMHO, thats a great deal for you. There is at least a grand tied up in tearing it down, media blasting and primer. Jump on it. I wouldnt haggle too much. Just make sure you get everything and catalog what you're getting, where it is and so on. The only downside is that you wont have the...
  12. trailpsycho

    Power Steering Resevoir

    I originally used an Astro reservoir that I added a second nipple to (from a second Astro rez). Problem is the Astro rez is just too darn small...the pump was always cavitating. I ran it that way for two years. I recently made a reservoir out of steel. I am a little concerned about how hot...
  13. trailpsycho

    Want EFI/Auto Tranny... What would you do?

    You have a couple of options... As G mentioned, swap the intake for EFI off of any 5.0, add in the wiring harness and you will be set. Firing order isnt that important lots of people run 5.0 HO EFI electronics with non-roller cams, earlier firing order and have great performance. You will...
  14. trailpsycho

    power steering bleeding issues..

    Mark- Pull the coil wire...so it cant fire. Turn the motor over a few times-this flows fluid more slowly than if the engine 'catches'. Cardinal rule is never to actually fire the engine to intially prime the system. Always use the starter--with the engine disabled. Apparently, you have alot...
  15. trailpsycho

    STC top installation - Anyone do a little re-work??

    I think Rusty might be onto something there. Any chance that you have the bows backward--ie installed the cams on the wrong bows? That or as another poster mentioned...mine has I believe multiple positions for the cam to be mounted. Also are you sure you have the base (on the bed rails)...
  16. trailpsycho

    Crate motor?

    What kind of driving, drivetrain, budget, etc? Its a loaded question. Lots of great options...but it really depends on how "old school" you want to keep it VS going new tech (late model EFI or mod motor) VS diesel. The easiest (on the pocket book and tech-wise) is a 5.0 roller block with...
  17. trailpsycho

    clutch issues AGAIN !!

    OK, back up. Its unclear what setup you are running. First off, do you have the original mechanical linkage or a hydraulic setup. If you have a hydraulic, is it stock Ford parts or aftermarket parts. I ask this b/c it will make a difference if you have the integrated slave VS an external...
  18. trailpsycho

    Official welcome of DirtDonk to the WH team

    Definitely sounds like a Win-Win to me. Paul is good peeps. Best to both. Just dont go too "Corporate" on us, Paul.
  19. trailpsycho

    gears/traction?

    I run this set-up...almost exactly. Its a great drivetrain. Couple of things to consider. Highway travel, how much will you be doing. Also where do you live? The reason why I ask is that even a healthy 302/5.0 will not be a rocket-ship on hills and grades. I do a decent bit of road...
  20. trailpsycho

    EFI right the 1st time...

    I wouldnt swap any heads on that motor...unless you were going to spring for some aftermarket aluminum heads. Otherwise, its just not really worth it. The gains for the GT40s will be minimal. 15-20 HP. The Explorer is great to get as a package...short front dress, GT40 heads, better intakes...
Top