• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

302 oil pump not pumping?

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Some members here can pull an engine out of a bronco quicker than they can pull the pan off of an installed engine in a bronco.
So your logic, and that of your builder are just as sound as pulling the pan off in situ for inspection.
I usually do things the hard way, and would have struggled to remove the pan in the vehicle. But sitting here, and as an armchair quarterback, I say pull the engine.
While everything‘s still mostly apart it sounds like?
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Losing prime isn't the issue. When you install a new pump it's dry. You spin it CCW and it primes itself. The drill like mentioned several times already will create enough torque that you'll really feel it while holding it while priming the engine.

The key to us helping is knowing whether the drill was actually cranking the pump or not. If the pickup tube wasn't attached properly it could be the cause if the shaft is properly inserted into the pump.

Engine running "noisy" could be from no oil in the lifters.

Sorry to hear about your hassles but you need to pull the engine. 4 min is a LONG time w/o oil pressure.
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
I thought that as well. But after asking my engine rebuilder said even running only 4 minutes without oil would cause issues. He is like why use the time dropping the pan instead of pulling it. So, I guess its a fair point.
Gotcha. Fair enough!
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
I’m at the does it even have an oil pump in it stage…. Like nvrstuk, it will self prime, if it’s turning, and the pickup is not clogged or improperly installed, period. So that leaves a few questions like did the person who went through the top put an oil pump in it? Did the old oil look like sludge? Are you one hundred percent sure oil pump is turning?

I mean, plenty of rusty restoration shows pulling vehicles out of decade old undergrowth in a field, and start right up.

Unless you have a vehicle lift, I say pulling a most likely ruined engine is better than blowing time on your back later to find you need to pull the motor.

If you are getting no torque on drill, you are not turning the oil pump, have you tried pulling the hex drive shaft out? It may not be seated in pump drive.

Look at this and next video, upside down block showing how it looks inside and how it can be messed up




My last ditch thought, if for some reason the oil pump tolerance is large enough that it can’t self prime, and you have tried putting oil in through oil filter fitting, I’d try a last ditch attempt and unload a 20 or so second spray of wd40 or other spray lube to try to lube that oil pump before you pull everything apart.
 
Last edited:

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,115
why not just pull the pan?
Pulling a pan sucks. Then you have to inspect everything. Probably replacing stuff.
Considering we are expecting problems, if you can pull the engine it would be best. Little work up front. Easier overall.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I am in the habit of installing my mechanical oil pressure gage in the sender port any time I fire a fresh engine. Then I never have to wonder what the pressure actually is, and since I'm usually pretty busy in the first few seconds...I like to see the pressure while I'm under the hood.

If I were you...I would:
1. Screw in a decent direct reading oil pressure gage at the sender. (no tee's, or splices. Just abandon the factory sender, and run the direct gage under the hood.
2. Do what @nvrstuk recommended, and spin up the oil pump CCW with a cheap drill motor. You can definitely feel the difference as it primes, pressurizes, and starts to regulate. You will also see confirmation from the gage.
3. If you get good oil pressure in less than 5 seconds...then the oil pump is working. (and probably always did)
4. If you do NOT get good oil pressure in less than 5 seconds...the engine ran for 4 minutes w/o oil, and it's coming back out.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
My valve covers are always on -unless I'm adjusting valves or looking for oil flow when cranking the oil pump shaft. (or taking poser pics) lol
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
well its just for the oil pump preprime, then covers, intake, blah blah.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
I know. :)

I shouldn't have posted but there are more than a few guys building engines that see more dirt when being built than they ever will in their lifetime under the hood. (wasn't implying your's is/was/ever been) :)
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
In short… I dropped the pan because the oil looked good when I drained it. If I wiped out the cam I would have expected to see some metal flake in the oil but I really didn’t. So I took the chance and took the pan off. From a glance everything seemed to be clean. I dropped the oil pump it to seemed clean. I put pump with the pickup tube in a tote filled with the oil I just pulled out. I spun it with a drill but still no oil. Then I put a little oil down where it should pump out of. That was the trick… I primed it and at that point I could spin it with the drill and oil pumps right out. I proceeded to put it back together with new oil. With the distributor off I used the drill and spun the oil pump unit oil was finally coming out at the value rockers. I did that a few times just to make sure! Put the valve cover back on and dropped the distributor back in and fired it right up.

Obviously my timing wasn’t there but it sounded ok but I didn’t let it run to long because my oil gauge was only reading a hair over 20 at high idle being cold. Obviously 20 is LOW but worse is it started to fall to 8 psi. I don’t have a stock cluster but a Digital Dakota which I got used. I haven’t ever used one before which I’m not sure if they need calibration… maybe 20 really isn’t 20? Or maybe this oil pump is totally going out?

Pull distributor valve cover back off and spun it with a drill to see if it’s getting oil?

Drop the pan again and new oil pump?

Any thoughts on this?

Thanks Jeff
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
My thoughts are like B4 your oil pump is toast.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Just because you don't have shavings Doesn't mean you don't have potentially some serious damage to your bearings and cam
 

Wild horse 75

Sr. Member
Joined
May 9, 2023
Messages
464
Loc.
BC
Low oil pressure can be caused by excessive clearance in the main and rod bearings. You might be best served to yank it out now and take a good look at everything. I would also go pick up a mechanical pressure gauge that you can install to really see what the pressure is. Dakota digital gauges don’t need to be calibrated but you can change to work with different senders.
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Yeah after I fired it up and only had 20 on the gauge wasn’t reassuring! Once the pressure started to drop I shut it off.

Yes I can certainly drop the pan again. It really didn’t take me all the long. I think a new oil pump is $50?
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Low oil pressure can be caused by excessive clearance in the main and rod bearings. You might be best served to yank it out now and take a good look at everything. I would also go pick up a mechanical pressure gauge that you can install to really see what the pressure is. Dakota digital gauges don’t need to be calibrated but you can change to work with different senders.
Good point!
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Plastigauge is your best friend before firing anything back up.

Being the way I am, I would pull the engine, disassemble and inspect everything then reassemble per the book check all tolerances.

Tim
 
Top