• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

FiTech EFI pre-order info

work765

Full Member
Joined
Aug 27, 2015
Messages
279
Are you sure you're still getting the proper voltage signal when the key is in the START position? The computer needs that to work properly, which is why I thought of that when you mentioned the WSOD (white screen of death) on the module.

Are you having the FiTech control timing too, or just the fuel?

And what is your drain? How fast does the battery go dead? If within a few hours, it's usually either your alternator or just a tired battery.

Good luck.

Paul



Called tech. He said it might be that I have my red wire hooked to my solenoid and not directly to the battery terminal. He said the starter is drawing power the same time as the unit.

I'll try moving that red wire to the terminal.

And no, no timing control. I'm running the 400hp unit. I Read too many timing issues on here; I wanted to avoid any problems.

The drain isn't too bad. It will be slow to boot if I let sit for a few days. But overnight i don't think it's too bad. (Granted this was when it was carbed) so maybe the fitech needs more accurate power.

Also I already have the cold start up by 10. I might adjust the initial prime squirt. But according to fitech. That's a universal adjustment. And can't be set for cold or warm. So it will always shoot more regardless of temp.

I'll report back with my findings. Thanks guys


Sent from my iPhone using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Even though this unit is less finicky and troublesome with old stuff than some others, any electronic control unit really does need that more accurate, or clean power than our Broncos usually provide on their own.

It's always a good idea to upgrade wiring or at least the grounding scheme on an EB whenever electronics are installed.
Maybe you did that already, but many have not yet so I thought it worth repeating.

Paul
 

68stang73

Sr. Member
Joined
Nov 29, 2015
Messages
399
^^^^^^ yes make sure you have clean power and ground. The reason I mentioned the cold star was mine started after about 6 revolutions until I adjusted the values and now it starts within 1-2. I sure helped mine and the off idle stumble.
 

englewoodcowboy

Lick Creek Restorations
Joined
Jul 25, 2010
Messages
4,201
Well a brief update on mine, I am running a Aeromotive Stealth in tank fuel pump and it apparently draws a bit more than the FiTech can handle and I have some melted wires. FiTech was consulted when I purchased the fuel pump so they are warranting repair/replacement of my unit and I am going to run the fuel pump on its own circuit with a relay. A pain in the ass to pull out and redo but I am glad to know this is a potential issue before I get others out there. At least I happen to have 2 more units on the shelf so down time will only be an afternoon... other than that, the FiTech is amazing with timing control etc. I have tweaked and tuned my system and could not be happier with the performance and MPG to boot. Lots of power and getting 15mpg at 70mph is not bad at all in my books.
 

work765

Full Member
Joined
Aug 27, 2015
Messages
279
Even though this unit is less finicky and troublesome with old stuff than some others, any electronic control unit really does need that more accurate, or clean power than our Broncos usually provide on their own.

It's always a good idea to upgrade wiring or at least the grounding scheme on an EB whenever electronics are installed.
Maybe you did that already, but many have not yet so I thought it worth repeating.

Paul



Paul, so putting my red wire directly onto my battery and not solenoid was the final solution. This morning before work and after work I tested it when cold. It fires right up!! So all this time it was that. The handheld has come on every time perfect since I changed the wire over.

And now that it's starting up like it should, I'm pretty damn happy with this system. It's definitely driving the best it ever has.


Sent from my iPhone using Tapatalk
 

charlesawhite

Jr. Member
Joined
Oct 14, 2010
Messages
70
Mine was running good for about 1000 miles then it suddenly died. Fault code P0202 Injector failure shows up and I tried to reset per Fitech instructions this weekend but it didn't work. Injector doesn't cut out and just floods engine with gas. Anyone else have this issue? I'll call Fitech again Monday and see if there is another solution before I yank it off and send it back.
 

jimschulz

Full Member
Joined
Sep 6, 2013
Messages
215
Loc.
Eastern Washington
I jst got an RMA from FiTech on Friday to send mine back due to injector problems. Mine is the left primary injector that has failed and wont inject but only a dribble. Hopefully their turnaround is pretty quick, and really hope this doesnt become a common theme.... ;D
 

tony-runner

New Member
Joined
Dec 17, 2015
Messages
11
Inreresting... please keep us posted on those injector problems..... mine still in a box. Planing to install it this winter.

1971 M-code Mach 1
 

charlesawhite

Jr. Member
Joined
Oct 14, 2010
Messages
70
Fitech is sending me a new injector to install myself. It's the left primary as well. I guess we'll see if that fixes the issue. They said they would send it out tomorrow morning.
 
Top