• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Instrument gauges reading without engine running

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I am working on a 1970. My water temp gauge wasn’t moving off cool (didn’t seem to move at all) and my oil pressure gauge was pegged all the way at max with the engine running. I replaced the temp sensor and now as soon as I turn the key on without the engine running my water temp gauge maxes out and I noticed the oil pressure gauge will go to approx 40 without the engine running. The fuel gauge seems to be accurate but at times will go from full to empty and then back to normal. I added a ground from the dash to the inner fender supports but that didn’t seem to help. Any thoughts? Thank you
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Well, the ground was a good idea and can only help things in the long-run, so it's a good thing to leave in place.
But it sounds like the other two have issues all their own.

Try this first. Unplug the wires from the sending units and see what the gauges do. The gauges are always "active" when the key is on, but what you're seeing now is current actually passing through them on the way out the sending unit wires. Disconnecting the senders will at least let you know if the fault is in the senders, or somewhere closer to the gauges.

I'd start there at least and see if that narrows anything down.

Paul
 

oldiron

Bronco Guru
Joined
Jul 21, 2005
Messages
1,054
Did you get the sending units for gauges? Or the ones for lights?
Makes a difference.
Greg
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I second disconnecting the senders. The gauges should be dormant with the sensor unplugged.

Second, what senders did you spec out? The senders match the body, not the engine. IF the engine is swapped and someone speced senders for the donor vehicle and not a Bronco that would be a problem.

Another issue (I don't think this is you) is when someone gets a sender there is often an option for gauge/light. The sender for the light is much cheaper, but won't work with a gauge.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I second disconnecting the senders. The gauges should be dormant with the sensor unplugged.

Second, what senders did you spec out? The senders match the body, not the engine. IF the engine is swapped and someone speced senders for the donor vehicle and not a Bronco that would be a problem.

Another issue (I don't think this is you) is when someone gets a sender there is often an option for gauge/light. The sender for the light is much cheaper, but won't work with a gauge.[/QUOTE

The sender I picked up is TS58 Standard Motors Product. I told the parts counter I needed a temp sender for a 1970 Bronco 302. The said this was a exact replacement. I will disconnect senders tomorrow are see what happens.

I appreciate everyone’s help.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I unplugged the senders and turned the key on and they didn’t move. I plugged them back in started the bronco and oil went straight to 90 and water temp climbed to hot. I shut the engine off and turned the key on and they started to climb again.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the old test for a gauge on the dash is to unplug the wire at the sender and touch it to a good clean ground.
The gauge should go full sweep.
You can also figure out if the wires are going to the correct senders this way.
If the temp gauge goes full sweep when you ground the temp gauge wire, and the same for the oil pressure gauge, I would say the senders are either the wrong ones, or are bad.
Good luck
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I checked the gauge by grounding it out and it goes full sweep. I tried to run a separate wire from the sender to the back of the temp gauge and plugged it in where the red/white wire should be and turned the key on and needle still goes full sweep. I double checked ground on cluster, cleaned IVR to clear off any rust, same thing. I have tried 2 different senders and both do same. Any thoughts? Thank you for everyone’s help.

When I turn key on the needle goes full sweep then I start the engine the needle slowly moves to 180 after the bronco engine runs a few minutes
 
Last edited:
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I checked the IVR and I’m getting 12 volts out of it with the key on I purchased a new IVR and I’m getting between 3 to 5 votes out of it l. It’s a Scott Drake one however now none of my gauges work. The gas gauge moves a little and just seems like it gets stuck and goes back to empty. The oil and temp no movement at all. I have the cluster grounded to the dash and the dash grounded to the inner fender. I have new senders for oil and temp.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sounds like the old one was toast and the new one is putting out at least close to the proper voltage.
Are you using a digital volt-meter, or an analog where you can see the needle moving? Seems like 3-5 is just maybe one volt low. That won't keep your gauges from acting properly. It will just make them read slightly lower than if it was 4-6 volts.
If yours is adjustable like the originals though, once you get things sorted you can see if the gauges seem to be reading a bit low (all three slightly low) you can tweak the adjuster screw/dashpot/rheostat/thingy to get them up a bit.

Now you should go back to the earlier test of grounding out the sending wires. This should push the needles at a steady rate up to near their full sweep. Maybe not all the way if the voltage is slightly low (I could be wrong on the voltage expected though), but at least you should get a result you can quantify.

Paul
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I’m using a digital meter. I will try to ground out the gauges next. Is it possible the would move full sweep with the bad IVR but not the new correct voltage output one?

I appreciate your help.

Thanks



Sounds like the old one was toast and the new one is putting out at least close to the proper voltage.
Are you using a digital volt-meter, or an analog where you can see the needle moving? Seems like 3-5 is just maybe one volt low. That won't keep your gauges from acting properly. It will just make them read slightly lower than if it was 4-6 volts.
If yours is adjustable like the originals though, once you get things sorted you can see if the gauges seem to be reading a bit low (all three slightly low) you can tweak the adjuster screw/dashpot/rheostat/thingy to get them up a bit.

Now you should go back to the earlier test of grounding out the sending wires. This should push the needles at a steady rate up to near their full sweep. Maybe not all the way if the voltage is slightly low (I could be wrong on the voltage expected though), but at least you should get a result you can quantify.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If the IVR is supplying any voltage to the gauges, they will move at least part of their sweep when you ground a sending unit wire. If the voltage is low, then the needles may not go full sweep. If it's high, they may go beyond their normal limit, or move more quickly to that limit.
But they only way they would not react at all is if the voltage supplied was extremely low, or something else was wrong.

That 5v or 6v you're getting is more than enough to make the needles at least move to near the top, if not beyond.

Paul
 
Top