• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

More HP from 302??

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
He is asking how to get more power out of a 302. Gearing is how you do it. I'll make some simple numbers to follow along with...

Cruising at 2000 RPM you have 200 foot pounds of torque available. Bump that up to 2500 RPM and that warmed over 302 is now making 250 foot pounds of torque.

HP is torque x RPM / 5252. So a higher RPM where there is also more available torque makes more HP.

But wait, there more!
The added gearing also creates more mechanical advantage. Figure at a given speed there is a given amount of needed driving force. This overcomes aero drag, rolling resistance, grade, etc. Lets say you need 400 pounds of forward thrust for that speed. Not knowing the tire size I'll go with a generic 33" tire. Radius is 16.5", or 1.375 feet.
That is 550 foot pounds of torque out of the rear axle.
So what does the engine need to make to overcome this drag and make this amount of torque? Presuming that you have a normal old school non-overdrive transmission it comes down to the final drive ratio in the axle.
With 3.50 gears, you would need ~157 ft-lb torque out of the engine.
With 4.10 gears, you would need ~134 ft-lb torque out of the engine.

So with 3.50 gears and the engine turning a lower RPM you are nearly tapped out in power. Using 3/4 of the possible torque (also HP once you mix in the RPM)
But with 4.10 gears and the engine turning a little faster, and needing less torque on the driveshaft to get the job done you are now using a little over half the available power from the engine.

So gears in this case will make more power, and reduce the power needed to drive. Win-win. This is why we keep saying you need it geared correctly or making more HP is useless. Added HP to a given displacement engine generally means more RPM. Since the HP is a factor of torque and RPM, and the torque is fairly fixed for a given displacement based on cylinder pressure and that is limited by compression ratio and that is further limited by octane. The go to way of making more HP is to put the torque higher in the RPM band. Which with the wrong gearing will actually make things worse.
But if you look at adding displacement, that picks the whole torque curve up, which picks up the whole HP curve. So yes, big inch motors make more HP, that is merely a side effect of making more torque.

So does that make sense why gears are important and how big inch motors can make up for it?

For these V8s the fuel economy stays fairly stable up to about 3000 RPM for a given load. So more gear really doesn't both economy much.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The fact that only 1% of EB owners use stock or near stock tire sizes is a function of the group think that we see in EB owners. Land Rover owners are clearly more able to think for themselves. Talk to some of them and ask why they don't have 35" tires and lift kits. I have and they are firm in that they aren't mindless followers, that do things that some knuckle heads think looks cool. Almost all 50 yr. old Land Rovers look and work like Land Rovers all over the world did when new. They maintain their trucks rather than install 400+ HP Coyote engines that make no sense.
I've known CJ5 owners that think driving 80 MPH makes them macho. Some are still alive and still stupid. Others became organ donors.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Thanks for spending the time Broncobowsher...
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Oh and jkkkkysss. Give us all a break OK? One mind group thinkers? lol
Join a Land Rover forum and be happy. :)

As I drove into the same obstacle in 2 WD (thats rear wheel only) alongside the LRovers with my bit "macho" 37"s on a few years back to rescue not one but two of your highly coveted Land Rover drivers who probably still had 700x15" nylon tires on who were so hung up on body parts, spring hangers, on the frame, etc and of course still runnin back killing stock leaf springs.

You really need to come out of the '50's and '60's thinking and actually drive or own a Bronco that has some of these worthless upgrades you constantly bark about.

If you ever drove a Bronco in actual 4WD situations you might realize that a stock Bronco is a capable little rig but modified with all the upgrades you seem to detest and downplay in every one of your posts a modified Bronco can go in 2WD where they are ztruggling in stock form. NOT saying a stock Bronco is not a capable rig butwith all the off road options/upgrades you can bolt on (not my style) or modify and do yourself the difference is night and day.

I apologize if I offended anyone else but I got tired of the same relentless bashing for us as Bronco people and for our non stock Broncos.

Have a good day all.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Is there a stock bronco anywhere? Even the fully restored originals, have some mod to them...
 

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
Oh and jkkkkysss. Give us all a break OK? One mind group thinkers? lol
Join a Land Rover forum and be happy. :)

Whenever I read one of his posts, in my mind I hear and old man voice yelling "GET OFF MY LAWN, YOU DAMN KIDS". ;D
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
The fact that only 1% of EB owners use stock or near stock tire sizes is a function of the group think that we see in EB owners. Land Rover owners are clearly more able to think for themselves. Talk to some of them and ask why they don't have 35" tires and lift kits. I have and they are firm in that they aren't mindless followers, that do things that some knuckle heads think looks cool. Almost all 50 yr. old Land Rovers look and work like Land Rovers all over the world did when new. They maintain their trucks rather than install 400+ HP Coyote engines that make no sense.
I've known CJ5 owners that think driving 80 MPH makes them macho. Some are still alive and still stupid. Others became organ donors.
Your use of the term group think is essentially offensive.

I'll add, IMO land rover owners are the emitamy of your definition of snobbish uber rich "group thinkers". They are also the only ones who drive worse than hummer and BMW and Hyundai owners. They don't mod their vehicles because they don't know how. Read that again, they don't know how.

The ones that are modded look like this:

QbcO62y.jpg


There, I feel better now. :)

I've seen plenty of EB's with stock or as close to stock tires as can be recognized, hard to tell in the 29-31 inch range. Your argument that only 1% have stock tires is baseless.

Your argument that land rovers do not use larger tires is as well baseless., i think 33 or 35's here:

Twisted-Land-Rover-1.jpg



The fact EB owners do mod, shows they are the off-road entrepreneurs of the world, not some biscuit eating queens flat land farm truck from the UK.

I get it, first it was 31s, then 33, then 35, then 37 sized tires.

The only reason for those larger sized tires is to get over that one rock, one more than your bud with 35's or 33's. I'd be just as happy on 31's (my new ram1500 has those, and you cant go bigger without voiding everything), but it is what it is, an evolution. A Land rover has no evolution, it stays what it was from the factory.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Thanks for spending the time Broncobowsher...
I was not trying to piss anyone off, I was trying to say if your new to bronco's ,the information can get overwhelming;D and I do appreciate all the members write up and help. so I'll just delete my two post so it doesn't destact from the thread;D
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
I was not trying to piss anyone off, I was trying to say if your new to bronco's ,the information can get overwhelming;D and I do appreciate all the members write up and help. so I'll just delete my two post so it doesn't destact from the thread;D



You're good Savage!! Leave them up. No issue with your posts. Just the guy that once again offended about everyone in this group. Your post is fine.

Glad I wasn't the only one that was once again, dumbfounded by jkkkkklys post.%)
 

squeezer

New Member
Joined
May 12, 2016
Messages
33
Looping back around to the original question.

Careful old school tuning can deliver good gains on a basically stock 302.

Optimized ignition timing is easy to learn and almost free.
The same can be said for the carb tune.

Get the above two right and enjoy more power and better efficiency.

Next on the list would be cam timing. Getting the cam events right takes a timing set swap... Can be done without pulling the engine.

Have purposefully left adding a 4BBl intake and headers off this list. Many many people bolt parts on without proper tuning and wonder why they didnt see major gains...

With the engine out the best bang for your buck is a cam, followed by a set of modern heads.

A 2V iron manifold truck with a good cam will make more torque than a 4V header truck with the stock cam in the RPM band most people fine useful.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
The trick to building more useable power into a 302 is to keep your intake velocity up. That means DON'T OVERBUILD IT!
I used Windsor Jr. heads because they had smaller runners and 1'94" intake valves rather than the more common 2.02".
I used the Edelbrock Performer cam. It's a mild upgrade and has a good torque band.
I used an Edelbrock Performer intake. It's probably the lowest performing aftermarket intake on the market, but it's smaller ports keep the velocity high for good torque.
I chose to use a little Edelbrock 500 CFM Performer carb. It may sound small, but it's capable of moving more air than a 302 with hydraulic lifters is capable of pumping.
I use Hooker mid length headers, because if a Small Block Ford has a weak link, it's the exhaust ports.

This combination is quite drivable, and will still go sideways when you want.
We even use it to pull our 15' camp trailer for hunting at 8500' in the Sierra.

This 302 block has been rebuilt twice and is at the maximum .040" overbore. When rebuild time comes, I plan to use a roller 5.0 block, and just transfer my accessories. I see no reason for a 351W for my use.
 

McLeod

Full Member
Joined
Jun 29, 2008
Messages
296
^ This ^

Agreed. I have a 72 F100 and a 76 Bronco Wagon - both have mostly stock 302's with 3 speed transmissions (I know there are a lot of other factors as they are diff trucks). My Bronco has higher 3.5 gears and feels like Pepe Le Pew compared to my F100 which is super sluggish.

Your F100 has a higher ratio (lower numerically) than 3.55?
Was it originally an automatic truck?
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Had a 300 I-6/435 and 3:50 gears and ran 37s with no issues, If it were a 302 I would have dropped down to 4:56 on the gears. Need to be in the torque range of the motor.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
As the Mustang guys say, HP is how fast you hit the crowd, torque is how far you go into the crowd.

There's a balance.......

Tim
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I just watched Series 5 Episode 19 of Engine Masters.
It's really interesting and pretty much describes why the difference in character between a 347 and a 351W. They don't mention those engines, but they go into the principles of rotating mass, and how it affects horsepower and torque characteristics of a motor.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
lol pretty bad azz

Your use of the term group think is essentially offensive.

I'll add, IMO land rover owners are the emitamy of your definition of snobbish uber rich "group thinkers". They are also the only ones who drive worse than hummer and BMW and Hyundai owners. They don't mod their vehicles because they don't know how. Read that again, they don't know how.

The ones that are modded look like this:

QbcO62y.jpg


There, I feel better now. :)

I've seen plenty of EB's with stock or as close to stock tires as can be recognized, hard to tell in the 29-31 inch range. Your argument that only 1% have stock tires is baseless.

Your argument that land rovers do not use larger tires is as well baseless., i think 33 or 35's here:

Twisted-Land-Rover-1.jpg



The fact EB owners do mod, shows they are the off-road entrepreneurs of the world, not some biscuit eating queens flat land farm truck from the UK.

I get it, first it was 31s, then 33, then 35, then 37 sized tires.

The only reason for those larger sized tires is to get over that one rock, one more than your bud with 35's or 33's. I'd be just as happy on 31's (my new ram1500 has those, and you cant go bigger without voiding everything), but it is what it is, an evolution. A Land rover has no evolution, it stays what it was from the factory.
 

Huckit36

Full Member
Joined
Jun 19, 2014
Messages
180
Oh and jkkkkysss. Give us all a break OK? One mind group thinkers? lol
Join a Land Rover forum and be happy. :)

As I drove into the same obstacle in 2 WD (thats rear wheel only) alongside the LRovers with my bit "macho" 37"s on a few years back to rescue not one but two of your highly coveted Land Rover drivers who probably still had 700x15" nylon tires on who were so hung up on body parts, spring hangers, on the frame, etc and of course still runnin back killing stock leaf springs.

You really need to come out of the '50's and '60's thinking and actually drive or own a Bronco that has some of these worthless upgrades you constantly bark about.

If you ever drove a Bronco in actual 4WD situations you might realize that a stock Bronco is a capable little rig but modified with all the upgrades you seem to detest and downplay in every one of your posts a modified Bronco can go in 2WD where they are ztruggling in stock form. NOT saying a stock Bronco is not a capable rig butwith all the off road options/upgrades you can bolt on (not my style) or modify and do yourself the difference is night and day.

I apologize if I offended anyone else but I got tired of the same relentless bashing for us as Bronco people and for our non stock Broncos.

Have a good day all.

Thank you sir!
 
Top