• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

FiTech EFI pre-order info

rnrmp

Full Member
Joined
Mar 3, 2008
Messages
219
Loc.
owasso
Finished my install and all is great at this time, keeps getting better and better
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
Thanks for the pics bteustch. That's the same as I have mine. Guess I'm just used to a lighter pedal.%)
 

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
Finished my install and all is great at this time, keeps getting better and better
I have been driving it all day with a big smile on my face.

The Howell TBI had the filter stud coming up from the front of the throttle body because it had two injectors. This one comes up in the middle of the four injectors.

Couple that with my drop, offset filter base to miss the DUI distributor and my stud was about two inches off from hitting the filter lid. Some 1/4" all thread, heating and bending and filter is back in place.

I don't like my low pressure frame pump running all the time when I turn the key so I may add a fuel pump switch so I can turn it off to work on lights, etc... if I don't want the pump running. This is if FITech confirms that it is wired right and there is not way to program it differently.
 

bteutsch

Sr. Member
Joined
Jan 11, 2009
Messages
875
After I posted the pictures I moved the throttle up one hole to the smaller hole that's a little higher and it actually made the pedal easier to press.
2ae334a801ec4ecea13013a3bb2f04b8.jpg
 
Last edited:

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
Here is how where I connected mine. uploadfromtaptalk1441551903789.jpg
 

Attachments

  • uploadfromtaptalk1441551922559.jpg
    uploadfromtaptalk1441551922559.jpg
    84.4 KB · Views: 243
OP
OP
TeamG

TeamG

New Member
Joined
Aug 14, 2011
Messages
41
Just a quick note directly from FiTech about repacement parts...


All electronic sensors are OEM parts that can be found at your local parts house. Here are a few on rockauto.com

Coolant Temp Sensor $5.32

http://www.rockauto.com/catalog/moreinfo.php?pk=4588416&cc=1303366&jnid=557&jpid=0

Oxygen Sensor $54.79

http://www.rockauto.com/catalog/moreinfo.php?pk=1193179&cc=1418587&jnid=749&jpid=1

Throttle position sensor $14.59

http://www.rockauto.com/catalog/moreinfo.php?pk=41473&cc=1028056&jnid=850&jpid=2


Thanks!

Sales at FiTech EFI

Reach us at 951-340-2624 or Sales@FiTechEFI.com
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
I went ahead and made a bushing and used the large hole all the way back. works great so far. Couldn't be happier with this throttle body set up for now.
 

Attachments

  • carb linkage 001.jpg
    carb linkage 001.jpg
    113.7 KB · Views: 221

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
I went ahead and made a bushing and used the large hole all the way back. works great so far. Couldn't be happier with this throttle body set up for now.

Can you give us some more details on how you make the bushing?
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
sure. I just used two washers that the diameter fit inside the large hole with a 1/4" hole through. Than I used two washers with a larger diameter and 1/4" hole with one on each side to act as a clamp. Works well but I'm still going to order the bushing that's made for it. Just don't want to wait!
 

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
sure. I just used two washers that the diameter fit inside the large hole with a 1/4" hole through. Than I used two washers with a larger diameter and 1/4" hole with one on each side to act as a clamp. Works well but I'm still going to order the bushing that's made for it. Just don't want to wait!
Can I get the part# for the bushing that is made for that top hole?
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
Well I got to say that I drove close to 150 miles today without so much as a hiccup. Funny thing is that as I pulled up UPS was here with the unit I returned to Edelbrock for testing. The only paperwork I got back with it is a packing slip saying it was tested/repaired. So I'm not really sure what the issue was that they found and repaired but for now it will go on my shelf of shame and bad ideas.
Felt good to drive the truck again. Haven't put any real miles on it since December. Wife says there is a noticeable difference in my attitude today:cool:
 

englewoodcowboy

Lick Creek Restorations
Joined
Jul 25, 2010
Messages
4,201
I would be interested in learning more and possibly getting in on the buy if it is a good deal. Does the system control timing or is it stand alone?

Edit: I called and spoke with their techs, great group of guys, they pointed out that they are getting a lot of interest from this group. If the discount is 15% or greater I am in on the buy. The system does have timing control and you do not need an external CDI box as it is fully capable of doing everything itself. This was great news for me and translates to even more savings.
 
Last edited:

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
I would be interested in learning more and possibly getting in on the buy if it is a good deal. Does the system control timing or is it stand alone?

Edit: I called and spoke with their techs, great group of guys, they pointed out that they are getting a lot of interest from this group. If the discount is 15% or greater I am in on the buy. The system does have timing control and you do not need an external CDI box as it is fully capable of doing everything itself. This was great news for me and translates to even more savings.
If you have the correct distributor it will control timing.
 

ChrisC74

Sr. Member
Joined
Dec 9, 2010
Messages
906
In seeing that they are selling out as fast as they are bringing them in and their price point is about half the other systems I think it might be a while before they offer anything like that.

I did let them know yesterday that we have a very active forum and a handful of us are installing their system and there is a lot of interest for their system. I think they are also hearing this from the Mustang and Corvette guys also...
 

bteutsch

Sr. Member
Joined
Jan 11, 2009
Messages
875
Got this from Bryce the other day on adjusting the idle.
The TPS reading will zero out every time you key off and allow the EFI save. What you are trying to achieve is to be at idle at operating temp with the IAC position between 5 and 10. To achieve this follow the steps below.

1. Bring engine up to operating temp. (around 180)
2. On the handheld go to Dashboard
3. Observe the TPS, IAC Steps, and Coolant temp readings
4a. If IAC Steps is zero and RPM is above target slowly close primary throttle blade screw (1/8 turn at a time) till IAC Steps start to raise to target 5-10 range.
4b. If IAC Steps are anything above 10 slowly open the primary throttle blade screw (1/8 turn at a time) until IAC Steps lower to the target 5-10 range.

NOTE: If TPS reading is 1.5 or higher the EFI doesn’t think the engine is in IDLE so it will raise IAC as a follower feature. To reset TPS just key off an allow EFI to power off. When EFI has saved the handheld values will go blank.


Bryce Cegielski
FiTech Fuel Injection
12370 Doherty St. Suite A
Riverside, CA 92503

Phone – 951-340-2624
bryce@FiTechEFI.com
 
Top