• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel injection problem?

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
I have a 74 Bronco that has been converted to a 5.0 efi motor. I think the motor is from '93 or '94. It has a single stock rear gas tank. The fuel line , the fuel pump (in line, mounted on the frame) and the fuel filter have all been replaced. The rotor and spark plug wires are only 2 years old. The truck runs fine till the outside temp gets into the 90's. Then, every once in a while, the motor stutters, then kills. If I let it sit for a few minutes, it starts and runs fairly good. I talked to a guy at the Wisconsin Super Celebration and he told me he had the same problem. I took his advice and replaced the stock radiator with a 4-core radiator and added a 6 blade fan, and added a new shroud. It runs at about 165 deg on the hiway, but gets to 180 in town. That still isn't that hot, but it still kills. Have any of you guys had the problem or know how to remedy it? Any help would really be appreciated. Thanks.
 

blade

Contributor
Maker of sharp things
Joined
May 13, 2020
Messages
195
Loc.
Santa Fe
Do you Know if you still have spark when this happens? You can use an extra spark plug to diagnose by plugging it to one of your wires and cranking it over.
How are your fuel lines routed? Are they near the exhaust possibly causing vapor locking? You can take a can of starting fluid also and use some when it stalls, if it fires back up it is likely fuel.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
It is not a cooling issue. Chasing the wrong issue there.

If you have a tach and you can get it to stall at speed. That is vehicle momentium keeps the engine spinning over even though it isn't running. Look at the tach. If it is still reading, you can be fairly sure the ignition system is doing fine. If it drops to zero, but the engine is clearly spinning, there is an issue with ignition system.

What I am seeing a lot with that vintage EFI is failing capacitors in the computer. They literally are just aging out at this point. There are DIY kits to redo these yourself.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
What type EFI? T-body or Ford or other?

Your engine temps are actually to cool. EFI likes heat. 210ish is where most EFI's run the best.

Tim
 
OP
OP
BRONCITIS74

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
I imagine it has spark, cause it runs after a few minutes. I will check to routes of the fuel lines tomorrow as that sounds like it could be the problem. I just drove it and it misses a little like it did yesterday after it killed on me. It ran fine till I put some Brand X premium gas in it. Think that has anything to do with it?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
What was the engine temperature before you made the change? If it wasn’t overheating before, then it wasn’t an overheating problem.
Should run just fine at normal operating temperatures so need to check sensors, perhaps.
Maybe coolant temperature sensor, or intake air charge temperature sensor (if there’s one) or your BAP sensor.
Can you lay out for us everything about the engine? Is it an MAF, or speed density?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Lots of assumptions on my part, of course, but at this point, we really don’t know anything. Lots of testing and observation yet to be done.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I imagine it has spark, cause it runs after a few minutes. I will check to routes of the fuel lines tomorrow as that sounds like it could be the problem. I just drove it and it misses a little like it did yesterday after it killed on me. It ran fine till I put some Brand X premium gas in it. Think that has anything to do with it?
TFI's get hot...fail and then start to work after they cool down. Been there...done that....

Tim
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
My 94/95 EFI used MegaSquirt to control it is finicky when it gets hot. How is your hot re-start after it sits a few minutes but was running fine before you shut it off? If was running fine then it a pain to start you probably have fuel boiling. I am still trying to narrow it down but if I put the key on for 5 seconds, turn off, back one 5 seconds, off back on 5 seconds this forces the fuel pump to run several times and pressurizes the fuel rail. Then it starts and runs fine.

If you fuel is getting hot - lines run near the headers, exhaust or resting on engine parts combined with hot ambient air you may be boiling off your fuel and EFI can;t work with that in the lines. It just stumbles and dies. Next time it happens try the key on/off/on/off/on and see if starts up and runs ok.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Where do I look for a kit if I want to redo the capacitors?
First make sure it’s showing the right symptoms.
We know that when the capacitors fail the fuel pump runs continuously with the key on. Do we know of any other symptoms?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
First make sure it’s showing the right symptoms.
We know that when the capacitors fail the fuel pump runs continuously with the key on. Do we know of any other symptoms?
I've heard of a bunch of different issues. You would need to find an EEC-IV speciality (mustang?) forum for all the details.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Where is the fuel pump mounted? Too far from the tank or too high up is just inviting vapor lock between the tank and pump. The suction side of the fuel line has a vacuum on it and it doesn't take much heat to make that fuel boil. Combine that with a return style fuel system that heats the fuel and it gets worse. An in tank pump eliminates this and is the simple fix.
 

Wild horse 75

Sr. Member
Joined
May 9, 2023
Messages
464
Loc.
BC
My money is on the TFI module. Cheap enough to buy a new one and easy enough to replace on the side of the road when it dies. Make sure you put a good coat of dielectric grease on the back side where it meets the distributor.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Pretty sure it’s supposed to be a thermal transfer compound.
Does dielectric grease have the same properties? Or maybe some of them do and some of them don’t?
Either way make sure it has thermal transfer qualities.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Pretty sure it’s supposed to be a thermal transfer compound.
Does dielectric grease have the same properties? Or maybe some of them do and some of them don’t?
Either way make sure it has thermal transfer qualities.
No, dielectric grease is not thermal transfer compound.
The custom gaming computers also use the thermal transfer paste to pull heat out of the processor and into the cooling blocks. They get into different compounds. I forget what is the latest "best stuff". Not a gamer, but with with a few.
 

blade

Contributor
Maker of sharp things
Joined
May 13, 2020
Messages
195
Loc.
Santa Fe
No, dielectric grease is not thermal transfer compound.
The custom gaming computers also use the thermal transfer paste to pull heat out of the processor and into the cooling blocks. They get into different compounds. I forget what is the latest "best stuff". Not a gamer, but with with a few.
You can get thermal transfer paste at most Best Buy stores.
 
Top