• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel tank sending unit problem

eslusser

New Member
Joined
May 19, 2021
Messages
25
I just installed a new sending unit in the rear tank on my 77 but I am getting no reading on the fuel gage. The old unit would register but never went above 3/4. Any ideas on where to look next?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Did you happen to test it before you put it into the tank by attaching the electrical connector to it? If so did it give a reading outside of the tank when you pushed it through the range of motion?

Not going above 3/4 full is a fairly common issue even when these things were new. Have not heard that about the '77 specifically, but the earlier models this was practically a way of life for some.
Did your old one go down well below empty as you were getting close to no fuel?

For now, remove the connector from the tank and jumper the two contact points together with a bit of wire or whatever. Go up and turn on the key and watch the gauge. If it's slowly rolls it's way up in fits and spurts to beyond full in a few seconds, the gauge and the system are working properly and you've isolated the issue to the new sending unit.

If it does not act like this, then you have other issues.
Is this a dual tank setup, or just the single?

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
In one way that's a good thing. In this case it eliminates the switch as a possible fault location. They do wear out, and often cause trouble with the gauge reading accurately, or at all.
So all you need to do is start narrowing down some things. Checking the sender wires with the jumper is a good first step.

Paul
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
do you have a ground connection from the frame to the sending unit. then the wire from the sending unit to the panel gauge. if you short the wire to the gauge to ground the gauge should read full with the key on.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the other thing to check is each sender wire to fuel, oil, and water gauges should have @ 6 volts, pulsing on and off, with the key on. You can test with a test light.
Do the other gauges work?
Good luck
 
OP
OP
E

eslusser

New Member
Joined
May 19, 2021
Messages
25
I pulled the tank again and checked the connection. I am getting no power through the sending unit wire. Checked it with a test light. Thoughts on where to start to look next?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
sending unit wire is a ground wire. battery positive goes no further than the gauge. the resistance measure is worked through the ground coming from the frame through the fuel gauge resistor and up to the fuel tank toggle then to the gauge. it all measures ground resistance not incoming power to the gauge. same with the oil pressure circuit it works through its ground too. Same with water temperature.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
if you want to use a test light you will need to hook to battery positive then probe the wiring at the sender on the ground side.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, when your test light is grounded to the chassis, near the gas tank, you should see a dim bulb blinking every second or so. This is the signal from the IVR, through the fuel gauge on the dash cluster.
If you are not getting a flashing 6 volt signal at the sender there Is a problem either with the fuel gauge, the IVR, or the wire from the fuel gauge to the sender.

Do the temp and oil gauges work?

Good luck
 
OP
OP
E

eslusser

New Member
Joined
May 19, 2021
Messages
25
Oil, amp and other gages working. Just did the wire test by grounding test lite to the frame and I am getting a blinking lite by probing the wire from the gauge. Not sure why it did not cause gage to move earlier when I crossed connected the two terminals at the plug.

This tells me my new sending unit is bad?
 

Yooper74

Full Member
Joined
Aug 13, 2020
Messages
322
Did you do an ohm check on it? See if it’s reading in correct range 10-70 ohms.
 

Oleguy 74

Jr. Member
Joined
Sep 23, 2017
Messages
62
rusty truck.power from ivr goes through gauge.it gets its ground from sending unit in tank.sending unit is just a verible resistor
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, since you have the blinking signal at the end of the wire, near the fuel tank, if you somehow ground the wire, to a good clean ground, the fuel gauge should go full sweep. That is the next thing I would check.
The amp gauge is separate and has nothing to do with the fuel, temp, and oil.
Good luck
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I am getting no power through the sending unit wire. Checked it with a test light.
Just did the wire test by grounding test lite to the frame and I am getting a blinking lite by probing the wire from the gauge.

That's two different results from the same wire, so could indicate either that your test methods are not consistent, or there is something wrong with the wire and/or connector.
What did you use to test the first time when you had no power coming through the wire/connector?

Maybe try it again and see if moving the wires around while you're testing results in erratic behavior of the reading.

Oil, amp and other gauges working. Not sure why it did not cause gauge to move earlier when I crossed connected the two terminals at the plug.
This tells me my new sending unit is bad?

Maybe...
As mentioned you can't use the ammeter as a guide in this case, since it's independent of the other gauges. But the Oil and Water gauges working tells you that the power supply to the gauges (the IVR, or instrument voltage regulator) is sending a signal through the gauges and out to the sending units.

But because these are different items, you could still have a bad fuel gauge (but it worked before, right?), a bad switch (with a single tank you do not have this switch), a bad wire between the gauge and sender (but the flashing light says that you at least have it sometimes), or a bad connector and/or bad ground connection.
The sending unit is the last thing to consider at this point because you jumpered the two contacts in the connector together and got nothing. This eliminates the sending unit as the only culprit, and opens up some more.

If you're getting a consistent signal/flash at the connector, keep trying to ground that wire out to see what your gauge does.
Instead of using the test light, and instead of jumpering the two connectors together, do as suggested by someone i think and connect that contact directly to a ground point on the frame, or body. Turn the key back to ON, or ACC and see if the gauge reads full now.

And follow the ground wire to it's termination point. Is it on the body, or the frame?
Because this does use a chassis ground farther back away from the battery than most other stuff, it never hurts to verify that you still have a good body ground like they originally came with from the factory.
At the battery negative terminal, how many wires/cables do you see? If only the one large ground cable down to the engine, you need to add another one to the body somewhere. And while you're at it you should add one from the back of the engine over to the firewall. This is a ground connection that Ford and most other manufacturers have used for decades for an improved setup. Unfortunately Early Broncos were never so lucky. So do yourself a favor and add one if it has not been added already.
If it's a later '77 maybe you even have one. I've never seen one even on '77's, but there are several members here that own '77 models that do have a ground strap at the back of the engine. So who knows? Maybe Ford got diligent and cut the EB a break towards the end of the run.

Paul
 
OP
OP
E

eslusser

New Member
Joined
May 19, 2021
Messages
25
I shorted the wire over at the tank and gauge did not move so I put a new gauge in. New Gauge immediately went to full level and sits there. I only put 4 gallons in so tank definitely not full.

Any ideas for what to look at next?
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, grounding the sender wire is only to test the circuit. What happens when you plug the wire to the sender? Four gallons is close to empty. Good luck
 
OP
OP
E

eslusser

New Member
Joined
May 19, 2021
Messages
25
It now goes to full and does not drop back unless ignition is off. Not sure why given tank is not full.
 
OP
OP
E

eslusser

New Member
Joined
May 19, 2021
Messages
25
I pulled the plug from the sending unit and the new gauge still shows full when ignition is on.
 
Top