What have you done to your Bronco today?

[399strokerEB]

Started install of Carter electric fuel pump. Made a bracket with a bunch of rubber grommets for dampening and to get it high enough to clear axle travel.

I've got one of those I need to install for my auxiliary tank to transfer into the main.

 

[Soylent]

Installed the M1A1tank and Duff rear diff skid.

 

[Jdgephar]

1st tank of gas in about 5 years and on the road!

Sent from my SM-S916U using Tapatalk

 

[gnsteam]

1st tank of gas in about 5 years and on the road!

Sent from my SM-S916U using Tapatalk

Looks so good. Congrates

 

[1969miller]

Worked all day yesterday cutting off brackets, cleaning old welds up, changing coil buckets, mounted my radius arms. Considering starting over again with a 3 link though..

 

[stupidboy]

Worked all day yesterday cutting off brackets, cleaning old welds up, changing coil buckets, mounted my radius arms. Considering starting over again with a 3 link though.. View attachment 914382

View attachment 914383

Those are some long arms! Call ‘‘em gorilla arms

 

[Ol'Blue]

Sold my old 302, cherry picker and engine stand after 400 miles on the new 351w. God, I hope the new 351 doesn't let me down as there's no turning back now!

 

[Yeller]

Sold my old 302, cherry picker and engine stand after 400 miles on the new 351w. God, I hope the new 351 doesn't let me down as there's no Turing back now!

Engine stands breed at my shop, don’t know how it happens, get down to one and year later there are 3

 

[Scoop]

Engine stands breed at my shop, don’t know how it happens, get down to one and year later there are 3

Wow! Down to 1, then 3? You should consider neutering your cherry picker!

 

[Yeller]

Wow! Down to 1, then 3? You should consider neutering your cherry picker!

There are 2 of them

 

[399strokerEB]

Polished up the paint a little and built a back bumper so I can get pulled out when I lawn dart the plow

 

[Howard2x4x4]

Worked all day yesterday cutting off brackets, cleaning old welds up, changing coil buckets, mounted my radius arms. Considering starting over again with a 3 link though.. View attachment 914382

View attachment 914383

Impressive long arms! DIY?

 

[stupidboy]

I’m getting ready to change to hydroboost , got one out of a 07 2500 Silverado

 

[Mikes Early Bronco]

I ordered an ARB locker for the front. Great Black Friday deal. Wouldn’t have known it without the reference from another Bronco owner. Very thankful.

 

[gnsteam]

A few days late with this post, but I brought home the chassis and roll cage from the restoration shop on Wednesday afternoon. Only pictures I took are of the body on a cart at the shop. Next week they will begin final strip and prepping for paint.

 

[BGBronco]

Soft top back on for the season. Get's to be more of a pain every year.

 

[Gsxr7000]

Pulled mine outside. Was attempting to hang led lights in the garage,but never started.

 

[hsach]

Been spending more time on my '78 lately, so the '67 has been sitting. Fired up the garage heater yesterday to start removing engine/trans/D20 so I can finish cleaning/painting the frame. It was going great until I needed to cut the bolt off the T-shifter to remove it from the trans adapter, not enough room even with 1" lift, and my Dremel died halfway through the bolt. 3rd one that has died in the last couple of years. Going to pick up another, but maybe I will try the cordless version, previous ones were all corded.

 

[hunter1]

Finally got around to installing disc brakes on the front.

 

[rocknhorse76]

Worked on dialing in the idle on my EFI 408W.