Search results

Drag Link I have to replace the drag link on a 67. It is an expensive little piece so I am just throwing in a little more and getting the stone crusher link and tie rod setup.

Tungsten grey I am going with the GT40 special edition scheme-Tungsten Grey with Silver shelby stripes. http://classicbroncos.com/photos/showphoto.php/photo/14835/limit/recent

Go to my Gallery. There is a new pic of the box of dash parts that I will be installing in the Terra Comp fiberglass dash that they said would be arriving this week. I got the custom switch panel from 12volt guy.com. He did a great job. He can build any panel you want. Parts to install...

Wiring In run my wiring from the Tuffy down through a hole and back up where it needs to be. It is all neatly tucked against frame in convoluted tubing. No wires show and the tubing protects from heat/dirt etc... No issues in a few years. My Alpine and JVC's both skipped on occassion. I have...

Seat wood When I replaced mine I used Starboard instead of plywood. It is a marine plastic that comes in all thicknesses and sizes. Any marine store can get it and most will just sell it by the square foot and cut it for you.

Vin # Location I cannot find the vin anywhere on my vehicle. No plate...I checked the frame rails from one end to the other all around. Can't find a thing. Any ideas> Title has U14NLA78814

Can you post another dash shot. I am in the process of rebuilding mine. Thanks

Crossmember How about the AOD is there crossmember modification required? I swapped a built up c-4 in my 69 for the 3 spd I will be swapping for an auto but want the AOD this time.

Looking for a set of the 1 piece fiberglass roadster door inserts. Need not be new as I will be repainting the whole truck soon

OHM sender The sender is 73 to 10 I just replaced with Autometer gauge and works perfect.

Voltage Regulator part # I installed the new voltage regulator and it is charging but it is drawing 1.5 volts from the battery when ignition is off. Old regulator was not charging. The old part# is Transpo f540HXD 12v 0377-It has a round plastic cylinder attached to a plastic plate on the...

Dead batt I replaced the voltage regulator yesterday. I disconnected the alternator completely and disconnected the negative battery cable. If I put the voltage meter between the negative battery cable and the negative battery terminal it reads 11.4 volts. Something is drawing somewhere. I...

Insurance-beware As an adjuster I can tell you that your agent is the last person you should believe. you need to get a copy of the actual policy including exclusions and valuation clauses. The classic car insurers like Hagerty sound good but if you read the policy it must be garaged...

Alt issue It is going dead while the truck is running. The alt was replaced correctly and the gauge showed it was charging the battery yesterday. While at the shop it was left running and charged battery up and ran great for 2 days. ALT Gauge showed 13 volts and alligator clipped tester...

Battery died a few days ago and I replaced the battery and the alternator. Ran the truck for 2 days and the battery died again. Any ideas????

Hood I am going to go with the WH Buckaroo hood on my new truck. I had the Pro-Flow on my last truck and it was very good- fit straight and was well built. http://www.wildhorses4x4.com/product/Buckaroo_Hood/Hoods

Key West I live in Key West. There are a few Broncos down here. http://classicbroncos.com/photos/showgallery.php/cat/500/ppuser/13928/sl/i

eadlock conversion Champion will do a conversion for you if you send in the wheels. Not much more and it gets done perfect. http://www.cwibeadlock.com/Conversions.htm

http://www.12voltguy.com/minitog.htm

Trail Cover I am in the same situation. I sent him a check on 10/18 and he cashed it 10/24. I have yet to see my cover. I emailed him on 12/1 and again on 12/5 to check status. No response. I tried to PM him but his mailbox was full. What is the story. I just want what I paid for! If he...